Obtenir 4 soumissions gratuites →Get 4 free quotes →Estimations.pro

Category: Guides in English

Renovation guides, prices and tips in English.

  • Ideal Indoor Humidity in Winter: Quebec Guide 2026

    The ideal indoor humidity in winter for most Quebec homes sits between 30% and 40%, and closer to 30% during deep cold snaps. That narrow window keeps your skin, sinuses and hardwood floors comfortable while stopping water from streaming down your windows, frosting the attic or feeding mould behind the furniture.

    In short: Health Canada recommends keeping relative humidity between 30% and 50%. In Montreal-area winters, aim for 30% to 40% and lower it toward 30% when it drops below −10 °C outside. Measure with a hygrometer before you buy a humidifier or a dehumidifier, and fix ventilation or air leaks first.

    What “relative humidity” really means in a Quebec winter

    Relative humidity (RH) is the amount of water vapour the air holds compared with the maximum it could hold at that temperature. The key word is relative: warm air can carry far more moisture than cold air. When −20 °C outdoor air leaks into a house and gets heated to 21 °C, its relative humidity collapses, which is why older, drafty homes feel parched every January.

    The opposite happens at cold surfaces. Warm, moist room air that touches a single-pane window, a poorly insulated corner or the underside of a roof deck cools down, its RH climbs to 100% and the water drops out as condensation or frost. The same house can therefore be “too dry” in the living room and “too wet” at the windows on the same day.

    Canadian federal guidance is consistent on the target. Health Canada’s guide to addressing moisture and mould indoors recommends maintaining relative humidity between 30% and 50%, using a dehumidifier when needed. The Canada Mortgage and Housing Corporation (CMHC) gives the same 30% to 50% range and suggests about 30% when it is colder than −10 °C outside.

    Ideal indoor humidity in winter: the target by situation

    Use this table as a practical guide. It translates the official range into what you should do when you read your hygrometer.

    Hygrometer reading (winter) What it usually means What to do
    Below 25% Very dry air, often from air leaks or a ventilation rate set too high Seal drafts, check HRV settings, then consider a humidifier
    25% to 30% Dry but acceptable during a cold snap Monitor; add moisture only if occupants feel discomfort
    30% to 40% The sweet spot for most Quebec homes in winter Keep doing what you are doing
    40% to 50% Acceptable in mild weather or with high-performance windows Watch windows and closets for condensation when it gets colder
    Above 50% Too humid for winter; mould and attic frost risk Increase ventilation, run fans, find the moisture source

    Newer homes with triple-glazed windows and good airtightness can hold slightly higher humidity without condensation. A 1950s bungalow in Ahuntsic or a Rosemont triplex with original windows will usually need the lower end of the range.

    Signs your home is too dry

    • Static shocks every time you touch a door handle or a light switch.
    • Dry, itchy skin, cracked lips, irritated eyes or frequent nosebleeds.
    • Gaps opening between hardwood floor boards, or squeaks that only appear in winter.
    • Wood furniture, doors or musical instruments cracking or going out of tune.
    • A hygrometer that stays under 25% for days at a time.

    Very dry air in winter is often a symptom, not the root problem. A house that leaks a lot of air constantly replaces moist indoor air with dry outdoor air. Sealing those leaks raises humidity naturally and lowers your heating bill at the same time.

    Signs your home is too humid

    • Water running down the inside of windows, or ice forming on the bottom of the glass.
    • Black spots on window sills, in closet corners on exterior walls or around the bathtub.
    • A musty smell in the basement or bedrooms.
    • Frost on roofing nails and on the underside of the roof deck in the attic.
    • Peeling paint or swollen trim near windows and exterior doors.

    High winter humidity is the more expensive problem. It feeds mould, rots window frames and can soak attic insulation. If you see condensation, our article on window condensation in winter walks through the causes and fixes, and frost in the attic explains what that white layer above your ceiling means.

    How to measure humidity correctly: 6 steps

    1. Buy a digital hygrometer. Basic models cost about $15 to $40 at hardware stores. Units with several remote sensors let you compare the basement, bedrooms and main floor.
    2. Place it away from moisture sources. Keep it out of the kitchen, bathroom and laundry room, and away from heaters, windows and direct sun.
    3. Give it time. CMHC notes that a hygrometer can take up to two hours to stabilize in a new location, so do not judge it after five minutes.
    4. Read it at the same time daily. Morning readings, after a night of breathing and before showers, are the most useful for spotting trends.
    5. Check calibration once a year. Inexpensive sensors drift, especially below 30%. A simple salt test (a sealed bag with damp table salt should read close to 75%) tells you how far off your device is.
    6. Compare with the outdoor temperature. Note the forecast low next to each reading. When it gets colder, your target should go down, not up.

    How to lower humidity in winter

    If your hygrometer regularly reads above 45% to 50% and windows are wet, work through these fixes in order. Most cost little or nothing.

    • Run the bathroom fan during every shower and for about 15 to 20 minutes afterward. Make sure it actually vents outdoors, not into the attic.
    • Use the range hood whenever you boil water or cook on the stove, and choose a model that exhausts outside.
    • Dry laundry in a vented dryer rather than on racks inside, and check that the dryer duct is clean and sealed.
    • Set your air exchanger properly. In winter, an HRV brings in dry outdoor air and pushes out moist indoor air. Raising its speed or using its dehumidistat is often the fastest fix. See our guide to air exchanger (HRV) costs in Quebec if your home has none.
    • Keep air moving. Open curtains and blinds during the day and avoid pushing furniture tight against cold exterior walls.
    • Look for hidden sources. A damp basement, a crawl space with bare soil, a leaking pipe or a large number of indoor plants can add surprising amounts of water vapour.

    A portable dehumidifier is rarely necessary on the main floors in winter, but it can help in a basement that stays damp all year.

    How to raise humidity safely when the air is too dry

    Before adding moisture, rule out the cause. Very dry air in a Quebec winter usually comes from air leakage or an HRV running too fast for the weather. Weatherstripping doors, caulking windows and sealing attic hatches is cheaper than running a humidifier all season.

    If the house is reasonably tight and still feels too dry, a humidifier makes sense. Keep these rules in mind:

    • Choose the right size for the room and use the built-in humidistat so it stops near 35% to 40%.
    • Clean the tank and filters as the manufacturer recommends; stagnant water can grow bacteria and mould.
    • Use distilled or demineralized water in ultrasonic models to limit the white dust they can release.
    • Turn the target down when the forecast calls for a deep freeze, and stop as soon as you see condensation on windows.

    Most Montreal-area homes heat with electric baseboards or ductless heat pumps, so a whole-house humidifier mounted on a furnace is only an option if you have a forced-air system with ducts.

    Humidity control costs in 2026

    Here are indicative price ranges in Canadian dollars for 2026, before taxes. Actual quotes depend on the house, access and the equipment chosen.

    Solution Typical cost (2026, indicative) Best for
    Digital hygrometer $15 to $40 (multi-sensor kits $50 to $120) Every home
    Portable humidifier $50 to $250 One bedroom or living area
    Furnace-mounted humidifier, installed $400 to $1,200 Homes with ducted forced-air heating
    Portable dehumidifier $250 to $500 Damp basements
    Bathroom fan replacement, vented outdoors $300 to $900 Steamy bathrooms, foggy mirrors
    HRV cleaning and balancing by a pro $120 to $300 Existing air exchangers
    Air sealing (weatherstripping, caulking, attic hatch) $300 to $1,500 Drafty homes with very dry air

    If your hygrometer shows high humidity and you already see black spots, have the source investigated before it spreads. A contractor can check ventilation, insulation and the building envelope, and a mould specialist can handle contaminated materials. You can compare mould removal quotes in Montreal before deciding.

    Condensation, frost or a tired air exchanger? Describe your project once and receive up to 4 free quotes from qualified contractors in Montreal, Laval, Longueuil and the surrounding areas. Get up to 4 free quotes →

    Frequently Asked Questions

    What should the humidity be in a house in winter in Canada?

    Federal guidance recommends 30% to 50% relative humidity indoors. In practice, Quebec homes do best at 30% to 40% in winter and around 30% when it is colder than −10 °C outside, to avoid condensation on windows.

    Is 50% humidity too high in winter?

    For most Canadian homes, yes. At 50% indoor humidity, cold windows and poorly insulated corners usually start collecting condensation once the outdoor temperature drops well below freezing, which raises the risk of mould and attic frost.

    Is 25% humidity too low?

    It is on the dry side and can cause static, dry skin and irritated sinuses. A short dip during an extreme cold snap is normal, but if readings stay that low, look for air leaks and check your air exchanger speed before adding a humidifier.

    Should I run my air exchanger in winter?

    Yes. An HRV is one of the best tools for controlling winter humidity because it replaces moist, stale indoor air with drier outdoor air while recovering much of the heat. Lower its speed if the air becomes too dry and raise it if windows stay wet.

    Why are my windows wet when my humidity is only 40%?

    Window condensation depends on the glass temperature as much as on humidity. Older double-pane units, failed seals or curtains that trap cold air against the glass can all cause condensation at moderate humidity. Lower the target a little and improve air circulation; if it persists, the windows themselves may need attention.

    Getting your home ready for the season? Our winterize your house checklist for Quebec covers the other jobs worth doing before January.

  • Hot Water Tank Replacement Cost in Quebec (2026)

    Hot water tank replacement cost in Quebec in 2026 is usually $1,100 to $1,800 for a standard 40-gallon electric tank swapped in the same spot, and $1,300 to $2,200 for a 60-gallon electric model, installation and removal of the old unit included. Gas, tankless and heat pump water heaters cost more, from about $2,200 to $6,500 depending on venting and electrical work.

    In short: since most Quebec homes heat water with electricity, the typical job is a like-for-like electric tank replacement done by a licensed plumber in two to four hours. The tank is roughly half of the bill; the rest is labour, fittings, the safety valve, a drain pan and disposal. All prices below are indicative 2026 ranges in Canadian dollars for the Greater Montreal area, before GST and QST. They are not official rates, and only written quotes for your home give you a firm price.

    Hot water tank replacement cost: 2026 price table

    The table covers the situations we see most often in Montreal, Laval, Longueuil and the West Island. Replacing a tank that sits in an open basement next to the electrical panel is the cheapest scenario. A tank tucked in a closet of a third-floor plex unit, or one that has to be moved, sits at the top of each range.

    Type of water heater Typical situation Indicative total installed (2026, before taxes)
    Electric tank, 40 gallons Condo, small household, same location and same wiring $1,100 to $1,800
    Electric tank, 60 gallons Family home, two bathrooms or more $1,300 to $2,200
    Three-element 60-gallon electric tank (peak-shaving models) Same wiring as a standard tank, smarter heating cycles $1,500 to $2,400
    Natural gas tank, 40 to 50 gallons Existing gas line and venting in good condition $2,200 to $3,800
    Gas tankless (on-demand) unit New venting through the wall, gas line sometimes upsized $3,500 to $6,500
    Electric tankless unit Small home or point-of-use; often needs a larger electrical service $1,500 to $4,000, plus any panel work
    Heat pump water heater Large unheated or semi-heated basement, condensate drain nearby $3,500 to $6,000

    Add 14.975% for GST and QST. A $1,600 replacement therefore comes to about $1,840 with taxes.

    What is inside a plumber’s quote

    Comparing two quotes line by line is the quickest way to spot the one that leaves out the drain pan, the expansion tank or the disposal fee. Ask each contractor to break the price down this way.

    Item Indicative price (2026) Why it matters
    Labour for a like-for-like swap $350 to $700 Draining, disconnecting, setting and connecting the new tank, testing
    Temperature and pressure relief valve and fittings $50 to $150 A new relief valve should come with every new tank
    Drain pan with drain line $60 to $200 Limits water damage when the tank eventually leaks
    Leak detector with automatic water shut-off $250 to $600 Cuts the main supply when water is detected on the floor
    Thermal expansion tank $150 to $350 Needed on some systems with a check valve or pressure reducer
    Thermostatic mixing valve $200 to $450 Lowers the temperature delivered to fixtures while the tank stays at 60 °C
    Relocating the tank $300 to $1,200 New water lines, wiring or venting to the new spot
    Removal and recycling of the old tank $0 to $100 Often included; check that it is written on the quote
    Evening, weekend or emergency call $150 to $400 extra A leaking tank rarely waits until Monday morning

    If your tank is leaking right now, our guide on emergency plumber costs explains how after-hours pricing works, and the plumber hourly rate guide helps you check whether the labour line is reasonable.

    Electric, gas, tankless or heat pump: which one for a Quebec home?

    Electric storage tank

    This is the default in Quebec, where electricity is the main energy source for most homes. Electric tanks are cheap to buy, simple to install, have no venting and rarely need anything more than the 240-volt circuit that is already there. The trade-off is standby heat loss: a larger tank keeps more water hot around the clock.

    Three-element 60-gallon tanks

    Hydro-Québec promotes 60-gallon three-element water heaters designed to shift heating away from winter peak periods, and has offered an instant rebate on these models through partner retailers. Check the amount in force on Hydro-Québec’s website before buying, since rebates change. These tanks can usually replace a standard 40-gallon unit without changing the power supply, which keeps installation simple.

    Gas tanks and tankless units

    Gas makes sense mostly where the house already has a gas line and a furnace or boiler on natural gas. Tankless units deliver continuous hot water and save floor space, but venting, condensate drains and gas line sizing push the price up quickly. An electric tankless unit for a whole house draws a lot of power and may require an electrical panel upgrade.

    Heat pump water heaters

    These units pull heat from the surrounding air, so they use far less electricity than a standard tank. In Quebec they work best in a large basement that stays reasonably warm, and they cool and dry the room around them, which is a bonus in summer and a small cost in winter. Ask the installer about noise, clearance and where the condensate will drain.

    Buy or rent your hot water tank?

    Renting a water heater is common in Quebec. Monthly fees usually run roughly $12 to $25 depending on size and contract term, with repairs and replacement included. Over a 12-year life, rental often costs more than buying, but it spreads the cost and removes surprise repair bills.

    Option Upfront cost Over 10 to 12 years Best for
    Buy and have it installed $1,100 to $2,200 (electric) Lowest total cost in most cases Owners staying in the home for years
    Rental contract Little or none Usually higher in total; maintenance included Owners who want fixed monthly payments
    Rent-to-own None Between the two Owners who want the tank to be theirs eventually

    Before signing a rental contract, read the early termination clause and the buyout price. They matter if you sell the house.

    Signs your hot water tank needs replacing

    1. The tank is 10 to 12 years old or more. Check the manufacturing date on the label; many home insurers ask about tank age, and some policies set conditions after a certain number of years, so read yours.
    2. Water is pooling under the tank, or rust is visible around the base or fittings.
    3. Hot water looks rusty or smells metallic, while cold water is clear.
    4. You run out of hot water faster than before, even though the household has not changed.
    5. The tank rumbles or pops when heating, a sign of heavy sediment in older units.
    6. The relief valve keeps dripping after being replaced.

    A leaking tank is not repairable. Shut off the water supply to the tank and the breaker, then call a plumber. If water reached the floor, our water damage restoration quotes page can help with drying.

    Quebec rules: temperature, licences and safety

    The Quebec Construction Code requires the water inside a home water heater to be kept at a minimum of 60 °C to prevent the growth of bacteria such as Legionella, which multiply in lukewarm water. The same Code limits the water coming out of bathtub and shower faucets to 49 °C in new plumbing installations, which is why a mixing valve or a pressure-balanced faucet is part of a proper job. Never lower the tank thermostat to avoid scalding; limit the temperature at the fixtures instead. The Public Health Agency of Canada gives the same advice in its guidance on water temperature, burns and scalds.

    In Quebec, plumbing work must be done by a contractor holding the right licence from the Régie du bâtiment du Québec, and plumbing contractors must also be members of the Corporation des maîtres mécaniciens en tuyauterie du Québec. A new circuit or a larger breaker is electrical work for a licensed electrician. Check the licence number on the quote before you sign.

    Grants for water heating change often. Our Quebec home renovation grants guide for 2026 lists the programs currently open; confirm eligibility before buying equipment.

    How to get the best price on a replacement

    • Replace before it fails. A planned swap on a weekday avoids emergency surcharges and water damage.
    • Get several written quotes with the same tank size and the same items (drain pan, relief valve, disposal) so the totals compare fairly.
    • Measure the space before choosing a 60-gallon tank; a taller or wider unit may not fit through a closet door.
    • Ask about warranty terms on the tank and on labour, and who handles a warranty claim.
    • Combine small jobs, such as a leaky shut-off valve or a new laundry faucet, into the same visit.

    Compare licensed plumbers in your area on our water heater replacement quotes page, or get up to 4 free quotes in a single request. It takes two minutes and there is no obligation.

    Frequently Asked Questions

    How much does it cost to replace a hot water tank in Quebec?

    In 2026, expect roughly $1,100 to $1,800 for a 40-gallon electric tank and $1,300 to $2,200 for a 60-gallon electric tank, installed, before taxes. Gas, tankless and heat pump units cost more, typically $2,200 to $6,500.

    How long does a hot water tank last?

    Most electric tanks last about 10 to 15 years. Hard water, heavy sediment and a tank that was never drained shorten that life. Plan for replacement once the tank passes 10 years rather than waiting for a leak.

    Is it cheaper to rent or buy a water heater?

    Buying is usually cheaper over the life of the tank. Renting spreads the cost and includes repairs, which some owners prefer. Compare the total of monthly payments over 10 to 12 years with the installed purchase price.

    Can I replace a hot water tank myself?

    In Quebec, plumbing work should be done by a licensed contractor, and a poor connection can cause water damage or a scalding risk. Insurers may also ask who installed the tank if you later make a claim.

    What size hot water tank do I need?

    A 40-gallon tank generally suits one to three people. Households of four or more, or homes with several bathrooms, are usually better served by a 60-gallon tank. Your plumber can confirm the size based on fixtures and habits.

    Ready to replace your tank? Request up to 4 free quotes from licensed plumbers in Montreal and the surrounding area.

  • How to Winterize Your House in Quebec: 2026 Checklist

    Learning how to winterize your house in Quebec is mostly about doing a short list of jobs before the first deep freeze: stopping water from freezing where it should not, keeping heat inside, and making sure your heating system, chimney and roof are ready for four or five months of hard use. Most of the work takes a weekend; a few items need a licensed pro.

    In short: shut and drain outdoor faucets, clean the gutters, service the heating system, test smoke and carbon monoxide alarms, seal drafts, and check the attic, roof and backwater valve. Doing it yourself costs little; hiring pros for the technical items usually totals a few hundred to about $1,500 in 2026, depending on the house. All prices below are indicative ranges in Canadian dollars, before GST and QST.

    In Montreal, Laval, Longueuil and Quebec City, deep cold, freeze-thaw cycles and heavy snow turn small oversights into costly claims: a hose left on an outdoor tap splits a pipe inside the wall, clogged gutters feed an ice dam, or a stuck backwater valve lets the sewer back up during a January thaw. Sealing air leaks before December also lowers every heating bill until April.

    The winterize-your-house checklist (outside)

    Start outside while the ground is still bare and the temperature is above freezing. Work through the list in this order:

    1. Shut off and drain outdoor faucets. Close the interior shut-off valve for each exterior tap, open the outdoor faucet to let the line drain, and leave it open. Disconnect and store garden hoses. Frost-free sillcocks still need the hose removed to work properly.
    2. Blow out the irrigation system. If you have an underground sprinkler system, have the lines purged with compressed air before the ground freezes.
    3. Clean gutters and downspouts. Remove leaves and seeds, make sure each downspout runs freely and discharges at least a metre or two away from the foundation. Blocked gutters are one of the main triggers of ice dams.
    4. Inspect the roof from the ground. Look for missing or lifted shingles, damaged flashing around the chimney and vents, and sagging sections. On a flat roof, clear the drains and scuppers.
    5. Check the chimney cap and exterior vents. Dryer, bathroom fan, HRV and furnace or heat pump vents must be clear and fitted with working flaps so snow and animals stay out.
    6. Seal foundation cracks and gaps. Fill small gaps where pipes and wires enter the house. Note any widening crack in the foundation for a pro to assess in spring.
    7. Protect the heat pump outdoor unit. Keep it raised above the snow line and clear around it. Do not wrap it in a tarp: it needs airflow to defrost.
    8. Prepare the driveway and walkways. Install snow stakes along the edges, store salt or traction grit near the door, and sign your snow removal contract before the first storm.

    The winterize-your-house checklist (inside)

    1. Service the heating system. Have the furnace, boiler or heat pump inspected, replace or clean filters, and make sure the thermostat works on every zone. With electric baseboards, vacuum the fins and test each one before it is needed.
    2. Test smoke and carbon monoxide alarms. Replace batteries, check the expiry date printed on each unit, and add a CO alarm near bedrooms if the home has any fuel-burning appliance or an attached garage.
    3. Seal air leaks. Re-caulk around window frames, add weatherstripping to exterior doors, and install foam gaskets behind outlet and switch plates on exterior walls.
    4. Insulate exposed pipes. Pipes in unheated crawl spaces, garages and along exterior walls need foam sleeves; in risky spots, a thermostatically controlled heating cable is safer.
    5. Check the backwater valve and sump pump. Open the backwater valve access, remove debris and make sure the flap moves freely. Pour water into the sump pit to confirm the pump starts and discharges outside.
    6. Look into the attic. Confirm the insulation is even and deep, and that soffit vents are not blocked. Frost on nails or the underside of the roof deck means warm air is leaking in.
    7. Set humidity correctly. In cold weather, keep indoor humidity low enough that windows do not stream with water. Run the HRV or air exchanger and bathroom fans regularly.
    8. Locate the main water shut-off. Everyone in the house should know where it is and how to close it quickly if a pipe bursts.

    DIY vs pro: what winterizing costs in 2026

    Many items are free or cost only materials. The technical ones are worth paying for, especially anything involving combustion, gas, electricity or working at height.

    Task DIY cost Pro cost (2026, indicative)
    Gutter cleaning (typical house) Free to $50 $150 to $400
    Furnace or heat pump tune-up Filter only, $15 to $60 $120 to $300
    Chimney sweep and inspection Not recommended $150 to $350
    Irrigation system blowout Not practical without a compressor $80 to $200
    Weatherstripping and caulking $50 to $200 in materials $300 to $900
    Pipe insulation and heat cable $20 to $150 $200 to $700
    Backwater valve check and cleaning Free if accessible $150 to $350
    Roof inspection Visual check from the ground $150 to $400
    CO and smoke alarms $25 to $80 per alarm Included with electrician visit

    Prices vary with house size, access, number of storeys and how busy contractors are. October and November are peak months for chimney sweeps and heating techs, so booking earlier in the fall usually means faster appointments.

    Heating appliances, chimneys and fire safety

    Wood stoves, fireplaces and oil or gas appliances need more attention than electric heat. Have the flue swept before the first fire of the season and ask the sweep to check the liner, cap and connections. Our guide to chimney sweep cost in Quebec explains what a proper visit should include.

    The Government of Quebec’s guidance on wood heating and fire prevention reminds owners to respect the manufacturer’s clearances, burn only dry wood and keep ashes in a metal container with a lid, stored outside away from the house. In Montreal, solid-fuel appliances may not be used during a smog warning.

    If you heat with a heat pump, cold-climate maintenance is different from summer care: see our heat pump winter maintenance guide for defrost, snow clearance and filter tips.

    Roof, attic and ice dam prevention

    Ice dams form when heat escaping from the living space melts snow on the upper roof and the water refreezes at the cold eaves. The fixes are almost always in the attic: more insulation, sealed air leaks around light fixtures and hatches, and open ventilation from soffit to ridge. Read ice dams on your roof for warning signs, and frost in the attic if you see white crystals on the roof deck in January.

    Owners of plexes and flat-roof homes should also clear drains before snow season and plan for snow removal on the roof after heavy storms. The flat roof winter checklist covers membranes, drains and flashing in detail.

    Water and flood protection before the thaw

    Winter water damage usually happens in two ways: frozen pipes that split, and sewer backups or seepage during a mid-winter thaw with heavy rain. Both are preventable.

    • Keep the heat on at least 15 °C or so in every room, including when you travel, and open cabinet doors under sinks on exterior walls during cold snaps.
    • If you leave for more than a few days, ask someone to check the house or close the main water valve and drain the lines.
    • Confirm the backwater valve is in place and accessible. Montreal and many suburbs require one on the sewer connection; if yours is missing, read backwater valve cost in Montreal.
    • Check the sump pump discharge line outside: if it freezes, the pump cannot empty the pit.
    • Clear snow away from basement windows and the foundation when it melts in late winter.

    Grants and tax credits that can help

    Some winter-related work can be partly funded. The Rénoclimat program run by the Government of Quebec covers eligible insulation, air sealing and other energy-efficiency work after an energy evaluation; check the Rénoclimat page on quebec.ca for current conditions. Hydro-Québec also offers its own rebates and winter peak programs, which are detailed on its website. Quebec seniors 70 and over may be able to claim part of their snow removal, gutter cleaning and similar services through the tax credit for home-support services offered by Revenu Québec. Check eligibility before signing a contract, since most programs require specific steps or contractors.

    Frequently Asked Questions

    When should I winterize my house in Quebec?

    Aim for mid-October to mid-November, before overnight temperatures stay below freezing. Outdoor faucets and irrigation lines are the priority; heating service and chimney sweeps should be booked in September or October to avoid waiting lists.

    How do I winterize my house if I am leaving for the winter?

    Keep the heat on at a safe minimum, close the main water valve and drain the plumbing, unplug non-essential appliances, and arrange regular visits by someone you trust. Tell your home insurer: many policies require a check every few days or a drained system when the house is empty.

    Do I need to cover my heat pump in winter?

    No. A heat pump outdoor unit should not be wrapped or covered in winter because it needs airflow to heat and defrost. Keep it raised above the snow, clear around it after storms and make sure no ice falls on it from the roof.

    What temperature should I keep my house at in winter to avoid frozen pipes?

    Keep every room heated, including basements and rooms you do not use. A minimum of roughly 15 °C is a common rule of thumb, but pipes along poorly insulated exterior walls can still freeze in a cold snap, so insulate them as well.

    How much does it cost to winterize a house?

    Doing the basic checklist yourself costs from nothing to about $300 in materials. Hiring pros for gutters, a heating tune-up, a chimney sweep and a roof check typically adds up to $500 to $1,500 in 2026, depending on the size and type of house.

    Get up to 4 free quotes for your winter prep

    Need a heating tech, roofer, plumber or snow removal company before the cold sets in? Describe your project once and receive up to 4 free quotes from contractors serving Montreal, Laval, Longueuil, the North Shore, the South Shore and the West Island. You can also compare snow removal quotes in Montreal before the first storm.

    Get up to 4 free quotes →

  • Air Exchanger (HRV) Cost in Quebec: 2026 Prices

    Air exchanger cost in Quebec in 2026 usually falls between $2,500 and $5,000 installed for a heat recovery ventilator (HRV) connected to an existing forced-air system, and between $5,000 and $9,000 when a fully ducted system has to be built in a house without ducts. A straight swap of an old unit on existing ductwork is often the cheapest job, at roughly $2,000 to $4,000.

    In short: the unit itself is usually $1,000 to $3,500; the rest of the bill is ductwork, wall or roof penetrations, controls, electrical connection and balancing. All amounts below are indicative 2026 ranges in Canadian dollars for the Greater Montreal area, before GST and QST. They are not official rates, and only written quotes for your home give you a firm price.

    Air exchanger cost in Quebec: 2026 price table

    Most Quebec homes fall into one of the situations below. Older plexes in Montreal and bungalows in Laval or Longueuil without ducts sit at the high end, while recent houses that already have an HRV in place are usually simple replacements.

    Project Typical situation Indicative total installed (2026, before taxes)
    Replacement on existing ducts Old HRV removed, new unit of similar size, same duct connections $2,000 to $4,000
    Simplified installation New HRV tied into the return of an existing forced-air furnace or air handler $2,500 to $5,000
    Exhaust-ducted installation Stale air drawn from bathrooms and kitchen, fresh air delivered through the furnace ducts $3,500 to $6,500
    Fully ducted dedicated system House heated with baseboards, new dedicated supply and exhaust ducts $5,000 to $9,000+
    Compact condo or apartment unit Wall- or ceiling-mounted unit, short duct runs $1,800 to $3,500
    Energy recovery ventilator (ERV) instead of HRV Same installation, core that also transfers moisture Add about $300 to $1,000

    Add 14.975% for GST and QST. A $4,000 installation therefore costs about $4,600 once taxes are included.

    Line-by-line breakdown of an HRV installation

    Ask each contractor to separate the items below. It is the fastest way to see whether a low quote leaves out the ductwork, the outside hoods or the balancing.

    Item Indicative price (2026) What to watch
    HRV unit $1,000 to $3,000 Airflow sized to the house; ENERGY STAR models use less fan power
    ERV unit $1,500 to $3,500 Useful in homes that become too dry in winter
    Insulated outdoor ducts and two exterior hoods $300 to $900 Intake and exhaust must be properly separated outside
    Interior ductwork $500 to $4,000+ The main variable; finished ceilings raise the price
    Wall control or timer switches $100 to $400 Bathroom boost timers are a common add-on
    Electrical connection and condensate drain $150 to $500 Most units need a nearby outlet and a drain line
    Airflow balancing $150 to $350 Often skipped by low bidders; it matters for comfort and efficiency

    HRV vs ERV: which air exchanger suits a Quebec home?

    Both machines replace stale indoor air with outdoor air while recovering part of the heat from the air going out. An HRV transfers heat only. An ERV transfers heat and some moisture, so it keeps a little more humidity inside in winter.

    • Choose an HRV if your house tends to be humid in winter: condensation on windows, musty basement, frost forming on the underside of the roof deck. Our guides on window condensation in winter and frost in the attic explain how excess humidity shows up.
    • Choose an ERV if the house is very airtight and becomes dry in January and February, with static shocks, dry throats or cracking wood floors.
    • Cold-climate defrost matters in either case. Ask how the unit handles long stretches below -25 °C and whether the defrost cycle is suited to your region.

    An installer who measures your home and asks about your habits (number of occupants, cooking, showers, laundry drying indoors) will recommend the right type more reliably than a one-size-fits-all quote.

    Signs you need a new air exchanger

    1. The unit is 15 to 20 years old and parts are hard to find.
    2. Motors are noisy, vibrate or stop for no clear reason.
    3. Condensation and mould keep returning even though the system runs.
    4. The core is cracked or warped and no longer seals properly.
    5. You are adding insulation and air sealing, which reduces natural air leakage and makes controlled ventilation more important.
    6. The current control has no humidity setting or the dehumidistat no longer responds.

    A cracked drain line or a dirty core is not always a reason to replace the whole machine. A cleaning and inspection, often $150 to $300, can tell you whether repair makes more sense. See our air exchanger cleaning quotes page for that service, or a specialized duct and HRV cleaning company such as Dry Master Systems Canada in Montreal.

    Rules, licences and the Rénoclimat grant

    Installing an HRV involves ventilation ductwork and an electrical connection. In Quebec, construction work must be done by a contractor holding the appropriate licence from the Régie du bâtiment du Québec. Before signing, check the company through the Régie du bâtiment du Québec and make sure the name on the quote matches the licence holder.

    On the financial side, the Government of Quebec page on Rénoclimat assistance for mechanical systems lists a $500 amount for installing or replacing a heat recovery ventilation system. Payment depends on your home’s EnerGuide rating improving between two consecutive energy evaluations. The program also warns that installing an HRV alone, without other work, could increase your home’s energy use and leave you ineligible. Register and book the first evaluation before any work starts, and confirm the amounts in force with your advisor, since Rénoclimat was updated on October 1, 2026.

    For the full picture of programs that can be combined with an energy renovation, read our Quebec home renovation grants guide for 2026. Natural Resources Canada also maintains a list of ENERGY STAR certified heat and energy recovery ventilators, which is a useful starting point when comparing models.

    Running and maintenance costs

    An HRV runs continuously at low speed in most homes, so fan efficiency affects your Hydro-Québec bill. Recent models with efficient motors draw far less power than units from the 1990s. Natural Resources Canada recommends annual maintenance to keep a ventilator at peak efficiency.

    • Filters: clean or replace them every one to three months during the heating season.
    • Core: wash it according to the manufacturer’s instructions, usually once or twice a year.
    • Outdoor hoods: keep them clear of snow, ice, leaves and lint, especially after storms.
    • Condensate drain: check that it flows and that the trap is filled with water.
    • Professional service: a yearly or every-other-year visit for cleaning and balancing typically costs $150 to $300.

    How to get the right price: step by step

    1. Note your current setup: heating type (baseboards, furnace, heat pump), existing ducts, square footage and number of bedrooms.
    2. List the problems you want to solve: condensation, odours, stuffy rooms, dry air.
    3. Ask for an on-site visit rather than a phone price; duct routing drives the cost.
    4. Request several written quotes with the same scope: unit model, duct layout, controls, balancing and warranty.
    5. Check licences and insurance before you sign.
    6. If you plan to apply for Rénoclimat, complete the pre-work evaluation first.

    Compare up to 4 free air exchanger quotes

    Prices for the same house can vary by thousands of dollars depending on how each contractor plans the ductwork. Describe your project once and receive up to 4 free quotes from ventilation contractors serving Montreal, Laval, Longueuil, the West Island, the North Shore and the South Shore.

    Get up to 4 free quotes now, or compare heating options in our guide to heat pump installation cost in Quebec.

    Frequently Asked Questions

    How much does it cost to install an air exchanger in Quebec?

    Most installations cost about $2,500 to $5,000 before taxes when the HRV can be connected to an existing forced-air system. Homes heated with baseboards that need a fully ducted system usually pay $5,000 to $9,000 or more. Replacing an old unit on existing ducts often costs $2,000 to $4,000.

    Is an HRV worth it in a Quebec home?

    In a well-insulated, airtight home, yes in most cases. An HRV removes excess moisture and indoor pollutants while recovering much of the heat from the outgoing air, which helps prevent condensation and mould during long winters.

    Should an air exchanger run all the time in winter?

    Most systems are designed to run continuously at low speed, with higher speeds for showers, cooking or high humidity. Turning it off for long periods lets humidity and pollutants build up. Follow the manufacturer’s settings and adjust the humidity control as outdoor temperatures drop.

    What is the difference between an HRV and an ERV?

    An HRV recovers heat only, which makes it a good choice for homes that are too humid in winter. An ERV recovers heat and some moisture, which suits very airtight homes that become dry. Both need the same type of installation and maintenance.

    How often should an air exchanger be cleaned?

    Clean or replace the filters every one to three months in the heating season and wash the core once or twice a year. A professional cleaning and balancing visit every one to two years keeps airflow and efficiency where they should be.

  • Wood Stove Installation Cost in Quebec: 2026 Prices

    Wood stove installation cost in Quebec in 2026 usually lands between $3,000 and $7,000 when a certified stove replaces an old one on a chimney that is still in good shape, and between $6,000 and $13,000 when a new insulated chimney has to be built through the roof. The stove itself is often less than half of the bill: the chimney, floor and wall protection, labour and permits make up the rest.

    In short: plan roughly $2,000 to $5,000 for a certified stove or insert, $500 to $1,500 for installation labour, and anywhere from a few hundred dollars to $6,000 for the venting system, depending on what is already in the house. All prices below are indicative 2026 ranges in Canadian dollars, before GST and QST, not official rates.

    Wood stove installation cost in Quebec: 2026 price table

    The table groups the most common project types in Montreal, Laval, Longueuil, the North Shore and the South Shore. Rural homes with long chimney runs or difficult roof access can sit above these ranges.

    Project type What it usually includes Indicative total (2026, before taxes)
    Replace an old stove with a certified stove Removal of old unit, new stove, new smoke pipe, connection to existing chimney in good condition $3,000 to $7,000
    Wood insert in a masonry fireplace Insert, full-height stainless steel liner, surround, sealing of the damper area $5,000 to $10,000
    New freestanding stove with new chimney Stove, hearth pad, insulated factory-built chimney through ceiling and roof, flashing, roof support $6,000 to $13,000
    Pellet stove Pellet stove, direct vent or short chimney, electrical outlet nearby $4,000 to $8,000
    Wood furnace or boiler added to central heating Certified unit, ductwork or piping tie-in, chimney $8,000 to $18,000+

    Add 14.975% for GST and QST. A $6,000 project becomes about $6,900 once taxes are included.

    Line-by-line breakdown: where the money goes

    When you compare quotes, ask each installer to separate these items. It is the easiest way to see whether one price is low because something was left out.

    Item Indicative price (2026) Notes
    Certified freestanding wood stove $1,800 to $5,000 Steel models at the low end, cast iron and soapstone at the high end
    Certified wood insert $2,500 to $6,000 Sized to the existing fireplace opening
    Installation labour $500 to $1,500 One to two days for most jobs; more for a new chimney
    Stainless steel liner (existing masonry chimney) $1,500 to $4,500 Often required for inserts and for old clay-tile flues
    New insulated factory-built chimney $2,500 to $6,000 Price rises with height, number of floors crossed and roof pitch
    Smoke pipe (stove to chimney) $200 to $600 Double-wall pipe reduces required clearances
    Hearth pad or floor protection $200 to $1,000 Ceramic or stone on a non-combustible base costs more
    Wall heat shield $200 to $800 Lets the stove sit closer to a combustible wall
    Removal and disposal of old unit $150 to $500 Heavy cast iron units on upper floors cost more to move
    Municipal permit Varies by town Check with your borough or municipality before work starts

    The rules every Quebec wood stove must meet

    Before choosing a model, check the legal side. It affects which stoves you can buy and, in some cities, whether you can keep using an existing one at all.

    Province-wide certification for new appliances

    Under Quebec’s regulation respecting wood-burning appliances, any wood heating appliance manufactured, sold or distributed in the province since September 1, 2009 must meet the CSA B415.1 standard or the U.S. EPA emission standard. In practice, any new stove from a reputable retailer is certified, but a used stove bought privately may not be. Look for the certification label on the back of the unit before you pay.

    Montreal: the 2.5 g/h limit and smog warnings

    The City of Montreal (montreal.ca) only allows solid-fuel appliances that emit less than 2.5 grams of fine particles per hour in its 19 boroughs, and bans the use of any solid-fuel appliance during a smog warning. If you live on the island, ask the installer for the emission rate on the certification sheet, not just the word “certified”. Several suburbs in Laval, the West Island and the South Shore have their own bylaws, so call your city before signing.

    Quebec City: deadline passed on September 1, 2026

    According to the City of Quebec (ville.quebec.qc.ca), since September 1, 2026 only wood-burning appliances certified CSA B415.1 or EPA may be used on its territory, and the city has run a subsidy program to help owners remove or replace older units. If you own an uncertified stove there, replacement is no longer optional if you want to keep burning wood.

    Safety guidance from the Government of Quebec

    The Government of Quebec’s page on wood heating fire prevention reminds owners to have the appliance installed according to the manufacturer’s instructions, to respect clearances to combustible materials and to keep the chimney clean. Follow the manual to the letter: clearances and floor protection are set by the manufacturer for each model.

    What makes wood stove installation cost go up

    • No usable chimney. Building a new insulated chimney through one or two floors and the roof is the single biggest cost jump.
    • Old masonry flue. Cracked clay tiles or a flue that is too large for a modern stove usually need a stainless liner from top to bottom.
    • Location in the house. A basement stove under a finished ceiling or a second-floor install in a plex means more chimney length and more finishing work.
    • Roof type and height. Steep roofs, metal roofing and three-storey buildings need extra safety equipment and flashing work.
    • Stove material and size. Cast iron and soapstone stoves cost more and are heavier to bring in.
    • Finishes. A stone or tile hearth and a decorative wall shield look better but add several hundred dollars.
    • Season. October and November are peak months. Booking in spring or summer usually means more availability.

    Step-by-step: how a typical installation goes

    1. Site visit. The installer measures the room, checks the existing chimney or roof path and confirms clearances.
    2. Model selection. You choose a certified stove sized to the space you actually want to heat, not the largest model in the store.
    3. Permit and insurer. You or the installer apply for any municipal permit, and you tell your home insurer about the planned work.
    4. Removal. The old unit and its pipe are taken out and the chimney is swept and inspected.
    5. Venting work. A liner is dropped into the masonry flue or a new insulated chimney is built through the ceiling and roof.
    6. Floor and wall protection. The hearth pad and any heat shields are installed to the manufacturer’s dimensions.
    7. Stove placement and connection. The stove is set, levelled and connected with the right smoke pipe.
    8. First fire and paperwork. The installer runs a test fire, explains break-in and gives you the invoice, model number and certification details for your insurer.

    Insurance, maintenance and running costs

    Most home insurers in Quebec want to know about any wood-burning appliance, and many ask for proof of professional installation or an inspection report. Call your insurer before the work: a surprise at renewal can cost more than the stove. Keep the invoice, a photo of the certification label and the installer’s details in one file.

    Once the stove is running, budget for an annual sweep. Our guide to chimney sweep cost in Quebec covers current prices and what a proper visit includes. Dry hardwood, small hot fires rather than smouldering ones, and a working carbon monoxide alarm near the stove are basic habits for every household.

    If you are weighing wood against other heating options, compare the numbers with our pages on heat pump installation cost in Quebec and electric furnace replacement cost. Many Quebec homes now combine electric heating with a certified wood stove as backup during outages and cold snaps. For programs that may apply to other parts of your project, see our Quebec renovation grants guide for 2026.

    Checklist before you sign a quote

    • Is the stove model named, with its CSA B415.1 or EPA certification and, in Montreal, an emission rate under 2.5 g/h?
    • Does the quote list the chimney or liner work separately, with length and diameter?
    • Are the hearth pad, wall shields and smoke pipe included, or billed as extras?
    • Who handles the municipal permit, and is its cost included?
    • Is removal and disposal of the old unit part of the price?
    • Has the installer worked with your type of chimney before, and can they provide references?
    • If carpentry, roofing or masonry work is involved, have you checked the company’s licence on the Régie du bâtiment du Québec website?
    • Are taxes, the labour warranty and the date of the first fire written down?

    Compare up to 4 free quotes for your wood stove

    Installation prices vary a lot from one company to another, especially when chimney work is involved. Describe your project once and receive up to 4 free quotes from heating and chimney contractors serving Montreal, Laval, Longueuil, the West Island, the North Shore and the South Shore.

    Get up to 4 free quotes now or see our chimney, fireplace and stove quotes page.

    Frequently Asked Questions

    How much does it cost to install a wood stove in Quebec?

    Most projects fall between $3,000 and $7,000 before taxes when a chimney in good condition can be reused, and between $6,000 and $13,000 when a new insulated chimney is needed. The stove, the venting and the labour are the three main parts of the price.

    Can I still use a wood stove in Montreal?

    Yes, if the appliance is certified and emits less than 2.5 grams of fine particles per hour, according to the City of Montreal. No solid-fuel appliance may be used during a smog warning, even a certified one. Older uncertified stoves and open fireplaces cannot be used to burn wood on the island.

    Do I need a permit to install a wood stove?

    Many Quebec municipalities require a permit or a declaration for a new wood-burning appliance or chimney. Rules differ from one city to the next, so check with your borough or town hall before work begins and keep the permit with your insurance file.

    Is a wood insert cheaper than a freestanding stove?

    The insert itself can cost about the same, but the total is often higher because most inserts need a full-height stainless steel liner in the masonry chimney. A freestanding stove connected to a sound existing chimney is usually the least expensive option.

    How long does a wood stove installation take?

    Replacing a stove on an existing chimney typically takes one day. Projects that include a liner or a new chimney through the roof usually take one to three days, plus any wait for the permit.

  • Frost in the Attic: Causes, Fixes and 2026 Repair Costs

    Frost in the attic is one of the most common winter surprises for homeowners in Montreal, Laval, Longueuil and the rest of Quebec: you climb up to check the insulation and find the underside of the roof deck, the rafters and every roofing nail covered in white crystals. A thin layer during a deep cold snap is not unusual, but heavy frost is a warning sign that warm, humid air from your living space is leaking into a space that should stay cold and dry.

    In short: attic frost forms when indoor air carries moisture through gaps in the ceiling and condenses on cold surfaces. The real fix is air sealing the attic floor first, then checking insulation and ventilation, and making sure bathroom and kitchen fans exhaust outdoors. Most targeted repairs cost between $800 and $4,500 in 2026, and Quebec’s Rénoclimat program can help with air sealing and insulation work. Prices in this guide are indicative 2026 ranges in Canadian dollars for the Greater Montreal area, not official rates.

    Why frost forms in the attic in winter

    In a properly built Canadian house, the attic is meant to stay close to the outdoor temperature in winter. The ceiling below it has an air barrier (usually the polyethylene vapour barrier and the drywall) and a thick layer of insulation. The problem starts when warm indoor air finds a path through that ceiling. Heated air rises, and the stack effect pushes it up through every opening it can find: light fixtures, plumbing stacks, the attic hatch, chimney chases and the tops of interior walls.

    Indoor air in winter holds far more water vapour than the frigid air outside. Once it reaches the attic, it meets the cold underside of the roof sheathing and the tips of roofing nails, and the moisture turns directly into frost. Natural Resources Canada explains in its Keeping the Heat In guide for roofs and attics that moisture in an attic is often carried up from the house as water vapour by air leakage, and that discoloured insulation is a tell-tale sign of where those leaks are.

    When a mild or sunny day follows a cold spell, the frost can melt faster than the attic dries and drip through the ceiling. Inspectors call this attic rain, and it is often mistaken for a roof leak.

    Signs of frost in the attic: a homeowner checklist

    Take a flashlight, stay on the joists and never step between them. Check for:

    • white frost or ice on the underside of the roof deck, especially near the peak and above bathrooms;
    • frost or rust stains around the points of roofing nails poking through the sheathing;
    • dark stains, black spots or water marks on the sheathing and rafters;
    • insulation that looks compressed, wet, clumped or darker in some spots;
    • water drops or stains on the ceiling below, sometimes around light fixtures or the attic hatch, appearing on mild days after a cold week;
    • heavy icicles and ice dams at the eaves, which often share the same cause: heat escaping into the attic.

    If you find stains but no frost, the moisture may come from an actual roof leak instead. Our roof repair price list for Montreal homes helps you compare that scenario.

    Is frost in the attic normal? How much is too much

    A light dusting of frost on nail tips during a week of -25 °C weather is common in Quebec and usually disappears without damage once temperatures rise slowly. What matters is the amount and how often it comes back. Natural Resources Canada notes that some frost buildup is to be expected, but a heavy buildup of about 10 mm (3/8 in.) or more calls for a closer look, starting with whether ventilation is present and not blocked by insulation.

    What you see Likely meaning What to do
    Light frost on nail tips only, gone after the cold snap Normal in deep cold Monitor once or twice a winter
    Frost layer on large areas of the deck Significant air leakage into the attic Plan air sealing and an inspection
    Frost thicker than about 10 mm, ice on rafters Major leak or blocked ventilation Book an inspection this winter
    Ceiling stains or drips on mild days Attic rain from melting frost Act quickly to limit damage
    Black spots, musty odour, soft sheathing Repeated moisture, possible mould or rot Inspection, cleanup and repairs

    Where warm air leaks into the attic

    These hidden openings are called attic bypasses. In Montreal-area bungalows and plexes, the usual suspects are:

    • Bathroom exhaust fans that dump humid air into the attic instead of outdoors, or ducts that are disconnected, crushed or uninsulated so they drip condensation.
    • Pot lights and other ceiling fixtures that are not airtight.
    • The attic hatch with no weatherstripping and no insulation on top.
    • Plumbing vent stacks and electrical wires passing through the top plates of walls.
    • Chimney and furnace flue chases, which need non-combustible materials and proper clearances, not ordinary foam.
    • Interior partition walls open at the top, dropped ceilings and bulkheads over kitchen cabinets, and joints where an addition meets the original house.
    • Ducts or equipment in the attic, such as an air exchanger or an air handler.

    High indoor humidity makes every one of these leaks worse. A humidifier set too high, laundry dried indoors, long showers without the fan, and an air exchanger that is off or poorly balanced all add moisture. Our guide to window condensation in winter explains how to tell when your indoor humidity is too high.

    How to fix frost in the attic, step by step

    Order matters: adding vents before sealing leaks can pull more house air into the attic.

    1. Lower indoor humidity now. Run bathroom fans during and for 20 to 30 minutes after showers, use the range hood when cooking, turn down or switch off any humidifier, and make sure your air exchanger is running with clean filters.
    2. Check the exhaust fans. Confirm that every bathroom and kitchen fan duct is connected, insulated and ends at an exterior wall or roof cap with a damper, never in the attic or a soffit.
    3. Do not scrape off the frost. Scraping damages the sheathing and drops ice into the insulation. Let it melt naturally once the source is controlled, and protect the ceilings below if dripping starts.
    4. Air seal the attic floor. This is the core repair. A contractor pulls back the insulation and seals bypasses with spray foam, caulking, rigid boards and fire-rated materials around chimneys and flues, then weatherstrips and insulates the hatch.
    5. Check ventilation paths. Soffit vents must not be buried in insulation; baffles keep an air channel open from the eaves. Roof vents should be clear. Add vents only if the inspection shows they are insufficient.
    6. Replace wet insulation and top it up. Insulation that stayed soaked or mouldy should be removed. Once the air sealing is done, blowing in more insulation reduces heat loss and ice dams.
    7. Treat any mould on the sheathing. Small areas can be cleaned by a qualified contractor; rotten sheathing must be replaced from the roof side.
    8. Re-inspect during the next cold spell.

    Air sealing and attic insulation go hand in hand. If your attic also needs more insulation, compare offers through our attic insulation quotes page, and if you find black spots on the wood, see our mould removal quotes.

    Attic frost repair costs in 2026

    Costs depend on attic size, access, how much insulation must be moved and any existing damage. These are indicative ranges for a typical single-family house in the Greater Montreal area, before taxes.

    Work Typical scope Indicative price (2026)
    Attic inspection Visual inspection, moisture readings, report $150 to $400
    Bathroom fan duct repair or rerouting Insulated duct to a roof or wall cap $250 to $700 per fan
    New bathroom exhaust fan installed Quiet fan, duct and exterior cap $350 to $900
    Attic hatch sealing and insulation Weatherstripping, insulated cover $150 to $500
    Air sealing of the attic floor Bypasses sealed after moving insulation $800 to $2,500
    Ventilation baffles and clearing soffits Baffles in each rafter bay along the eaves $300 to $900
    Additional roof or soffit vents Vents added where airflow is insufficient $400 to $1,500
    Removal of wet or mouldy insulation Vacuum removal and disposal $1.50 to $3.00 per sq ft
    Blown-in insulation top-up Cellulose or fibreglass to a higher R-value $1,800 to $4,500 for about 1,000 sq ft
    Mould treatment on roof sheathing Cleaning, treatment, encapsulation $1,000 to $4,000

    Add 14.975% for GST and QST.

    Grants for attic air sealing and insulation in Quebec

    Because attic frost is mostly an air-leakage and insulation problem, the repairs often qualify for energy-efficiency help. Under Quebec’s Rénoclimat program, the government offers between $400 and $800 for air sealing work, calculated according to how well you reach the air-change target set in your energy evaluation report. Roof insulation work must cover at least 20% of the total roof area to qualify, according to the Rénoclimat insulation page.

    Register and book the evaluation before starting the work, since the aid is based on a before-and-after comparison. For the latest changes, read our summary of what changed in Rénoclimat in 2026.

    Frequently Asked Questions

    Is frost in the attic normal in Canada?

    A small amount on nail tips during a long cold spell is common and usually harmless. A thick layer across the roof deck, frost that returns every cold week, or water dripping through the ceiling is not normal and points to air leakage from the house.

    Can frost in the attic cause mould?

    Yes. Repeated cycles of frost and melting keep the sheathing and insulation damp, which allows mould to grow and can eventually rot the wood. Black spots on the sheathing or a musty smell are signs that moisture has been present for several winters.

    Should I add more attic vents to stop the frost?

    Not as a first step. Ventilation helps remove some moisture, but if warm air keeps leaking in, extra vents can increase the pull of house air into the attic. Seal the leaks and fix the exhaust fans first, then let an inspector judge whether ventilation is adequate.

    How do I get rid of frost in my attic?

    Reduce indoor humidity right away, make sure bathroom and kitchen fans vent outside, and leave the frost to melt rather than scraping it. The lasting fix is professional air sealing of the attic floor, followed by insulation and ventilation corrections if needed.

    Get up to 4 free quotes for attic repairs

    Frost in the attic is easiest and cheapest to fix before it turns into wet insulation, mould or ceiling damage. Describe your attic, the signs you have seen and your city, and receive up to 4 free quotes from licensed contractors serving Montreal, Laval, Longueuil, the South Shore, the North Shore and the West Island. Always check the contractor’s RBQ licence before signing.

    Get up to 4 free quotes now

  • Electric Furnace Replacement Cost in Quebec (2026)

    Electric furnace replacement cost in Quebec usually lands between $3,000 and $8,000 installed in 2026 when the existing ductwork can be reused, and higher when the electrical service, the ducts or the whole heating strategy has to change. With many furnaces in Montreal, Laval, Longueuil and the suburbs now 20 years old or more, a lot of homeowners are facing this decision, often in the middle of a cold snap.

    In short: a like-for-like electric furnace swap costs roughly $3,000 to $5,500, a higher-capacity unit with electrical upgrades $5,000 to $8,000, and a furnace paired with a central heat pump $12,000 to $22,000 before any rebate. All amounts in this guide are indicative 2026 ranges in Canadian dollars for the Greater Montreal area, before GST and QST. They are not official rates; only written quotes for your home give you a real price.

    Electric furnace replacement cost in Quebec: 2026 price table

    The price depends mostly on three things: the furnace capacity (in kilowatts), what the electrician has to change in your panel and wiring, and how much ductwork and air-handling work is needed. The table below summarizes the most common situations in Quebec homes.

    Project Typical situation Indicative price installed (2026, before taxes)
    Like-for-like replacement Same capacity (15 to 20 kW), existing ducts and breaker reused $3,000 to $5,500
    Higher-capacity furnace Larger home or addition, new breaker and heavier cable $4,500 to $7,000
    Replacement with panel upgrade Furnace plus a 200 A panel or service upgrade $6,000 to $10,000
    Electric furnace plus central heat pump New furnace or air handler with an outdoor heat pump $12,000 to $22,000 before rebates
    Conversion from oil or gas to an electric furnace Old unit and tank removed, new electrical circuit $6,000 to $12,000+
    Duct cleaning at installation Supply and return ducts in a single-family home $350 to $800
    Smart or programmable thermostat Compatible model installed with the furnace $150 to $450

    Add 14.975% for GST and QST. Emergency installations in January or February, when contractors are booked solid, often land at the high end of each range.

    What is included in an electric furnace replacement

    A complete quote should spell out every step, so you can compare contractors on the same basis. A proper job normally includes:

    • shutting off power and safely disconnecting the old furnace;
    • removing and disposing of the old unit;
    • setting the new furnace and connecting it to the existing supply and return plenums, with new transitions if the dimensions differ;
    • connecting it to an appropriately sized breaker and cable, replacing them if the new unit draws more current;
    • installing or reconnecting the thermostat and any humidifier or air exchanger interlock;
    • installing a new filter and checking airflow at the registers;
    • testing every heating stage and leaving you the warranty documents.

    If a quote only shows a single total with no detail, ask for a breakdown. Our guide to what a proper estimate should include is written for roofing, but the same reading method applies to heating quotes.

    Factors that drive the price up or down

    Furnace capacity

    Most Quebec single-family homes use a 15 to 25 kW electric furnace, while larger or poorly insulated homes may need more. A bigger furnace costs more to buy, and above a certain size it needs heavier cable and a larger breaker. A contractor should base the capacity on a heat-loss estimate of the house, not simply copy the label of the old unit.

    Electrical panel and service

    An electric furnace is one of the biggest loads in a house. Older homes with a 100 A service sometimes cannot handle a larger furnace, an EV charger and a heat pump all at once. Upgrading to a 200 A service is a separate job with its own cost and coordination with Hydro-Québec; see our electrical panel upgrade quotes page if your electrician flags this.

    Ductwork condition

    Reusing sound ducts keeps the price low. Leaky, undersized or poorly insulated ducts, especially in a crawl space or unheated garage, reduce comfort and may need sealing, insulation or partial replacement.

    Access and location

    A furnace in an open basement is quick to swap. Units in a tight closet, an attic or a finished basement with a drop ceiling take more labour.

    Brand and features

    Multi-stage elements, variable-speed blowers and heat-pump-ready air handlers cost more upfront but give more even heat and an easier path to adding a heat pump later.

    Electric furnace or heat pump: which makes more sense in 2026?

    An electric furnace converts electricity directly into heat, roughly one unit of heat for one unit of electricity. A cold-climate central heat pump moves heat from outside and can deliver significantly more heat per kilowatt-hour for much of the winter, then relies on the furnace’s electric elements as backup on the coldest days. That is why many Quebec homeowners now replace the furnace and add a heat pump at the same time, or at least choose a heat-pump-ready air handler.

    Criteria Electric furnace alone Electric furnace + central heat pump
    Installed price (2026) $3,000 to $8,000 $12,000 to $22,000 before rebates
    Winter heating cost Highest Lower for most of the season
    Summer cooling None Included
    Eligible for heat pump rebates Generally not on its own Possible if the model and installer meet program rules
    Maintenance Minimal Annual heat pump service recommended

    Our heat pump installation cost guide details prices by system type. If your budget only allows a furnace today, ask for a model that can accept a heat pump coil later, so the second step costs less.

    Rebates and programs to check before you sign

    Quebec rebates in 2026 focus on heat pumps and building envelope work, not on standalone electric furnaces. Before you sign, check the current rules yourself, because amounts and conditions change:

    • LogisVert (Hydro-Québec): offers financial assistance for eligible efficient heat pumps, including central systems, installed by participating companies. A furnace replaced on its own is generally not the targeted equipment. Our article on the LogisVert heat pump rebate explains the conditions.
    • Chauffez vert: this program for replacing oil or propane heating ended on March 31, 2026, according to Quebec.ca. If you are converting from oil, read your options now that Chauffez vert has ended.
    • Rénoclimat: the Government of Quebec program for energy renovations, which starts with an energy evaluation of the home. The full list of current programs is on Quebec.ca.

    Never assume a rebate is included in a quote. Ask the contractor to state in writing which program, which amount and who files the claim.

    Signs your electric furnace needs replacing

    Electric furnaces are simple machines, and many last 20 years or more with basic care. Replacement usually becomes the better choice when you notice several of the following:

    1. The furnace is more than 20 to 25 years old and parts are hard to find.
    2. Heating elements, sequencers or the blower motor have failed more than once in a few winters.
    3. Some rooms stay cold even with a clean filter and open registers.
    4. You smell burning dust or hot plastic beyond the first start of the season.
    5. Breakers trip when the furnace runs at full capacity.
    6. Your electricity bills keep rising without any change in how you use the house.
    7. You want air conditioning and a heat pump, and the old unit cannot accept a coil.

    A burning smell that persists or a breaker that trips repeatedly is a safety issue: turn the furnace off and call a licensed contractor.

    Licences and rules for furnace work in Quebec

    Connecting an electric furnace is electrical work. In Quebec, it must be done by a contractor holding the appropriate licence from the Régie du bâtiment du Québec (RBQ), and electrical installations must comply with the electrical chapter of the Quebec Construction Code. Ductwork and air-handling work may involve a ventilation or heating contractor with its own licence subcategory. Before hiring, check the company’s licence through the Régie du bâtiment du Québec and make sure the name on the quote matches the licence holder.

    Your contractor is responsible for any required declaration of work. Some municipalities also require a permit when the furnace is part of a larger renovation; ask your city or borough before work starts.

    How to get the right price: step by step

    1. Write down your current setup: furnace brand, age, capacity in kW (on the label), panel amperage, and whether you already have air conditioning.
    2. Decide on the scope: furnace only, furnace ready for a heat pump, or furnace plus heat pump now.
    3. Request several written quotes based on the same scope, so you compare like with like.
    4. Check each licence with the RBQ and ask for proof of liability insurance.
    5. Compare warranties: parts, heating elements, labour and how long each applies.
    6. Confirm the schedule, especially in winter, and how long you will be without heat on installation day (usually a few hours).

    You can describe your project once and receive up to 4 free quotes from heating and electrical contractors serving Montreal, Laval, Longueuil, the South Shore, the North Shore and the West Island. Get up to 4 free quotes for your furnace replacement, or browse our heat pump and heating quotes page.

    Frequently Asked Questions

    How much does it cost to replace an electric furnace in Quebec?

    Most like-for-like replacements cost about $3,000 to $5,500 installed in 2026, before taxes. Larger units, panel upgrades or ductwork changes can push the total to $6,000 to $10,000, and adding a central heat pump brings it to roughly $12,000 to $22,000 before rebates.

    How long does an electric furnace last?

    Many electric furnaces last 20 to 30 years because they have no combustion parts. Elements, relays and blower motors may need replacing along the way. Age alone is not a reason to replace a furnace that heats evenly and runs safely.

    Is there a grant to replace an electric furnace in Quebec?

    Not usually for the furnace alone. Current programs mainly target heat pumps and energy renovations. If you add an eligible central heat pump, part of the project may qualify for LogisVert, subject to the program’s conditions at the time of installation.

    Can I replace an electric furnace myself?

    No. Connecting a furnace involves high-amperage electrical work that must be done by a contractor with the proper RBQ licence. Doing it yourself creates fire risks and can cause problems with your home insurance.

    How long does an electric furnace installation take?

    A straightforward swap usually takes half a day to one day. Jobs that include a panel upgrade, new ductwork or a heat pump can take two to three days, and service upgrades may depend on Hydro-Québec’s scheduling.

  • Heat Pump Winter Maintenance: Quebec Guide and 2026 Costs

    Heat pump winter maintenance is what keeps a cold-climate heat pump heating efficiently from December to March in Montreal, Laval, Longueuil and the rest of Quebec. A few simple habits, a clean filter, a clear outdoor unit and a yearly service visit, make the difference between a system that runs quietly at -20 °C and one that ices up, short-cycles or leaves you relying on baseboards during the coldest week of the year.

    In short: check or clean the filters every month in winter, keep snow and ice away from the outdoor unit after every storm, let the defrost cycle do its job, and book a professional tune-up once a year, ideally in late summer or early fall. Most homeowners spend $150 to $350 a year on professional maintenance. All prices in this guide are indicative 2026 ranges in Canadian dollars for the Greater Montreal area, not official rates.

    Why heat pump winter maintenance matters in Quebec

    An air-source heat pump does not create heat; it moves heat from the outdoor air into your home. In a Quebec winter, the outdoor coil works in freezing, humid and often snowy conditions for weeks at a time. Anything that blocks airflow, whether a clogged indoor filter, a snowdrift against the outdoor unit or ice under the base, forces the compressor to work harder for less heat. Your electric backup (baseboards, an electric furnace or a dual-energy system) then picks up the slack, and that is when winter bills climb.

    Natural Resources Canada recommends regular filter care and annual professional maintenance in its heat pump guidance for homeowners, and Hydro-Québec gives similar advice about keeping the area around outdoor units clear.

    Monthly heat pump maintenance you can do yourself

    Most winter care takes ten minutes a month and needs no tools. Follow these steps in order, with the system turned off at the remote or thermostat before you touch an indoor unit.

    1. Clean or replace the filters. On a wall-mounted mini-split, lift the front panel, slide out the mesh filters, vacuum them and rinse with lukewarm water if needed. Let them dry completely before putting them back. On a central ducted system, replace the furnace or air-handler filter with the size and rating your installer specified, typically every one to three months.
    2. Check the vents and registers. Furniture, curtains or holiday decorations in front of an indoor head or supply register reduce airflow and comfort.
    3. Look at the outdoor unit. From a window or the yard, confirm the fan is turning when the system is heating, the coil is not encased in ice and the base is not sitting in a block of snow.
    4. Listen for changes. Rattling, grinding or a new loud hum deserves a service call before it turns into a breakdown in January.
    5. Note your settings. Make sure the system is in heat mode, not auto, so it does not switch to cooling on a sunny afternoon.

    Protecting the outdoor unit from snow and ice

    The outdoor unit is where most winter problems start. Quebec storms, roof runoff and plow piles can bury a unit in a few hours. After every significant snowfall:

    • Clear snow from around and on top of the unit with a broom or a plastic shovel, leaving at least 30 cm (12 in) of free space on all sides.
    • Make sure the back and sides of the coil are not packed with blown snow, especially on units installed close to a wall or fence.
    • Keep the area below the unit open so defrost water can drain away. Ice building up under the base eventually reaches the coil and fan.
    • Never chip ice off the coil with a shovel, scraper or ice pick. The aluminum fins and refrigerant lines are easily punctured.
    • Do not wrap the unit in a tarp or a closed cover while it is in use. A heat pump needs open airflow all winter.

    Placement matters as much as shovelling. Units in Quebec are usually raised on a stand or wall bracket above the typical snow line and kept away from drip lines under roof edges. If yours sits directly on a pad at ground level, or water from the roof drips onto it and freezes, ask a contractor to raise it or add a small protective canopy designed for heat pumps. Gutters matter too: a blocked gutter above the unit is a classic cause of ice, and our guide to ice dams on your roof explains why meltwater ends up where you least want it.

    Understanding the defrost cycle (and what is not normal)

    When the outdoor coil frosts over, the heat pump briefly reverses to send warm refrigerant through it. During defrost, the outdoor fan stops, you may hear a whoosh, and a cloud of steam rises from the unit. Indoor heads may pause or blow less warm air for a few minutes. This is normal and can happen several times an hour in humid, near-freezing weather.

    These signs are not normal and call for a technician:

    • the coil stays completely covered in thick ice for hours and never clears;
    • the outdoor fan is blocked by ice or not turning while the compressor runs;
    • error codes flash on the indoor unit or the thermostat;
    • the system runs constantly but the house keeps getting colder;
    • water leaks from an indoor head instead of draining outside.

    If the unit is iced solid, switch it off and call for service rather than trying to force the ice off.

    Professional heat pump maintenance: what is included and 2026 prices

    A yearly visit by a qualified technician catches refrigerant leaks, electrical wear and dirty coils that you cannot see. Natural Resources Canada suggests servicing at the end of the cooling season, before heating starts, which in Quebec means August to October. A complete tune-up usually covers:

    • cleaning the indoor coils, blower wheel and drain pan, and testing the condensate drain;
    • cleaning and straightening the outdoor coil fins;
    • checking refrigerant pressures and looking for oil traces that signal a leak;
    • testing heating, cooling and defrost operation, including the reversing valve;
    • tightening electrical connections and measuring the compressor and fan motor amperage;
    • inspecting the line set insulation between the outdoor unit and the house;
    • a short written report with any recommended repairs.
    Service Typical situation Indicative price (2026, before taxes)
    Annual tune-up, single-zone mini-split One outdoor unit, one indoor head $150 to $275
    Annual tune-up, multi-zone system One outdoor unit, 2 to 4 indoor heads $250 to $450
    Annual tune-up, central ducted heat pump Outdoor unit, air handler or furnace coil $175 to $350
    Deep cleaning of an indoor head Coil and blower washed, mould or odour $200 to $400 per head
    Service call, frozen or iced unit Diagnosis, defrost issue, sensor check $125 to $250 plus parts
    Refrigerant leak search and repair Leak located, repaired and recharged $300 to $1,500
    Raising the outdoor unit New stand or wall bracket above snow line $250 to $700
    Protective canopy installed Shields the unit from roof drips and falling snow $150 to $500

    Add 14.975% for GST and QST.

    Thermostat settings that help your heat pump in winter

    How you use the system affects both comfort and wear. Modern cold-climate heat pumps run most efficiently at a steady temperature, so large overnight setbacks can trigger long recovery periods where backup heat kicks in. A modest setback of 1 to 2 °C is usually enough.

    If you have dual-energy service with Hydro-Québec or an oil or gas furnace as backup, ask your technician to confirm the switchover temperature is set correctly, so the heat pump runs whenever it is efficient and the backup only takes over in extreme cold. If you are unsure whether your unit is sized right for your home, our heat pump size calculator gives a quick estimate before you talk to a contractor.

    Winter heat pump checklist

    • Filters cleaned or replaced within the last month
    • Outdoor unit raised and clear of snow on all sides
    • No roof drip or blocked gutter above the unit
    • Drain area under the unit free of ice
    • System set to heat, not auto
    • Backup heat tested and working
    • Annual professional tune-up done and invoice kept for the warranty

    Choosing a heat pump technician in Quebec

    Heat pump installation and repair involve electrical work and refrigerant handling, so hire a company that holds the appropriate licence from the Régie du bâtiment du Québec (RBQ) and whose technicians are certified to handle refrigerants. Verify the licence number online, ask whether the visit is billed flat-rate or hourly, and request a written list of what the tune-up covers. If you are replacing an older unit rather than maintaining it, compare the long-term numbers in our heat pump installation cost guide for Quebec and check whether you qualify for the LogisVert heat pump rebate.

    Frequently Asked Questions

    How often should a heat pump be serviced?

    Once a year by a professional, ideally at the end of summer or early fall, plus monthly filter checks during the heating season.

    Should I cover my heat pump in the winter?

    No, not with a tarp or sealed cover while the system is running, because it needs airflow to heat. A small open canopy above the unit is fine and helps protect it from falling snow and roof drips.

    Why is there steam coming from my heat pump?

    Steam usually means the unit is in its defrost cycle, melting frost off the outdoor coil. It is normal and lasts a few minutes. Constant ice that never clears is not normal and needs a technician.

    Is it normal for ice to form on my heat pump?

    A light layer of frost that disappears after a defrost cycle is normal in Quebec winters. Thick ice covering the coil or the fan, or ice building up under the base, points to a drainage, defrost or refrigerant problem.

    How much does heat pump maintenance cost in Montreal?

    In 2026, an annual tune-up typically costs $150 to $275 for a single-zone mini-split and $250 to $450 for a multi-zone system, before taxes. Repairs found during the visit are quoted separately.

    Get up to 4 free heat pump quotes

    Need a winter tune-up, a repair or a new cold-climate unit? Describe your system once and compare up to 4 free quotes from heating contractors serving Montreal, Laval, the South Shore, the North Shore and the West Island. Start on our mini-split heat pump quotes page or go straight to the request form. Get my free quotes

  • Chimney Sweep Cost in Quebec: 2026 Prices and Guide

    Chimney sweep cost in Quebec in 2026 usually falls between $150 and $350 for a standard cleaning of a wood stove or fireplace flue, and between $250 and $500 when the visit includes a detailed inspection with photos or a camera scan. Repairs found during the visit, such as a missing cap, a cracked crown or a damaged liner, can add anywhere from $100 to several thousand dollars. For homes in Montreal, Laval, Longueuil and the rest of Greater Montreal, the fall rush makes November one of the busiest months to book.

    In short: budget about $200 to $300 plus taxes for a routine annual sweep of one flue in good condition. Heavy creosote, a tall or hard-to-reach chimney, a second appliance or urgent same-week service all push the price up. All amounts below are indicative 2026 ranges in Canadian dollars, not official rates.

    Chimney sweep cost in Quebec at a glance (2026)

    These ranges reflect typical residential jobs. Your quote depends on the type of appliance, the height and condition of the chimney, roof access and how much buildup the sweep finds.

    Service Typical situation Indicative price (2026, before taxes)
    Standard sweep, wood stove or insert One flue, annual cleaning, light to moderate soot $150 to $300
    Standard sweep, masonry fireplace Open fireplace, larger flue, smoke chamber brushed $200 to $350
    Pellet stove cleaning Venting, burn pot and heat exchanger $150 to $300
    Oil furnace chimney cleaning Older oil-heated home, often paired with furnace service $120 to $250
    Sweep plus detailed inspection report Home purchase, insurer request, new owner $250 to $500
    Camera inspection of the flue Suspected cracks, after a chimney fire $150 to $350 extra
    Glazed creosote removal Hard, shiny deposits that brushing will not remove $300 to $800
    Nest or debris removal Birds, squirrels, fallen bricks $150 to $400
    Chimney cap installed Missing or rusted cap with spark screen $100 to $350

    Add 14.975% for GST and QST. A $250 sweep becomes roughly $287 once taxes are included. A second flue at the same address is often discounted when both are done on the same visit.

    What is included in a professional chimney sweep

    A proper visit is more than running a brush up the flue. When you compare quotes, check that the following steps are part of the price rather than billed as extras:

    • Protection of the floor and furniture around the appliance, and a vacuum with a fine filter to contain soot.
    • Brushing of the full flue, from the roof or from below, with brushes sized to the liner.
    • Cleaning of the smoke pipe connecting the stove to the chimney, which clogs just as fast as the chimney itself.
    • A visual check of the cap, crown, flashing, liner joints and clearances to combustible materials.
    • Removal of soot and creosote from the home, plus a short written note of what was found.

    The Government of Quebec’s page on preventing fires with wood heating recommends having the chimney swept in spring, when deposits are still dry and easier to remove, so that any problem found can be repaired before winter. If you missed the spring window, book before your first regular fires of the season.

    What makes chimney sweep cost go up

    Two homes on the same street can get very different quotes. These are the factors that move the price the most:

    • Creosote level. Light, powdery soot brushes out quickly. Thick, tar-like or glazed creosote needs rotary tools or chemical treatment and takes much longer.
    • Roof access. A steep roof, a three-storey plex or a chimney far from the edge requires extra safety equipment and sometimes a second worker.
    • Chimney height and number of flues. Taller chimneys and buildings with several appliances simply take more time.
    • Appliance type. Open masonry fireplaces have a large smoke chamber that must be cleaned by hand, while some inserts must be pulled forward to reach the flue.
    • Timing. Requests peak in October and November. Booking in spring or summer is usually easier and sometimes cheaper.
    • Distance. Some sweeps charge a travel fee outside their main zone, for example from Montreal to the North Shore or to rural areas.

    How often should you sweep your chimney in Quebec?

    For most households that burn wood regularly through the winter, once a year is the baseline. Many sweeps recommend an extra mid-season cleaning if you heat mainly with wood and burn several cords in a season, or if you often burn damp wood, which produces more creosote.

    Usage Suggested frequency
    Occasional fires, a few weekends per winter Inspection every year, sweep every 1 to 2 years depending on buildup
    Regular evening fires all winter At least once a year
    Main heat source, stove running daily Once a year plus a check or cleaning mid-season
    Pellet stove Professional cleaning once a year, user cleaning as per the manual
    After a chimney fire or a long period without use Inspection before any further use

    Burning dry hardwood, keeping a hot fire rather than a smouldering one and following the manufacturer’s instructions all reduce creosote. They do not replace the annual visit.

    Wood-burning rules in Montreal and nearby towns

    Before paying to maintain an old fireplace, check whether you are still allowed to use it. According to the City of Montreal (montreal.ca), only solid-fuel appliances that emit less than 2.5 grams of fine particles per hour, certified to the EPA standard or to CSA B415.1-10, may be used in its 19 boroughs, and no solid-fuel appliance may be used during a smog warning, even a certified one. Several other municipalities in the Montreal region have adopted their own rules on installing or replacing wood-burning appliances, so check your town’s bylaw too.

    In practice, a sweep may tell you that your open fireplace or old stove cannot legally be used, and that the real choice is between replacing it with a certified unit, converting it to gas or electric, or sealing it. If you are rethinking how you heat your home, our guide to heat pump installation cost in Quebec compares the main options, and the Quebec renovation grants guide lists the programs currently open.

    Warning signs your chimney needs attention now

    Do not wait for the annual visit if you notice any of these signs:

    1. Smoke backs up into the room when the door is opened or the fire is lit.
    2. You smell a strong, acrid odour from the fireplace, especially on humid days.
    3. Black flakes or crumbs of creosote fall into the firebox.
    4. You hear a loud roaring sound or see dense smoke or sparks leaving the chimney, which can signal a chimney fire. Leave the house and call 911.
    5. Bricks, mortar or pieces of the crown are falling onto the roof or the ground.
    6. Water stains appear on the ceiling or wall around the chimney, often a flashing or crown problem.
    7. Animals or birds can be heard inside the flue.

    A working carbon monoxide alarm near any fuel-burning appliance and a smoke alarm on every floor are essential, whatever the age of the chimney.

    Common chimney repairs and their indicative prices

    The sweep often discovers problems that need a separate quote. These are the most frequent ones in Quebec homes:

    Repair Why it is needed Indicative price (2026)
    Crown repair or rebuild Freeze-thaw cracks let water into the masonry $300 to $1,500
    Repointing of the chimney Eroded mortar joints, loose bricks $500 to $3,000
    Flashing repair Leaks where the chimney meets the roof $300 to $1,000
    Stainless steel liner Cracked clay tiles, oversized flue, new insert $1,500 to $4,500
    Partial rebuild above the roof Leaning or badly deteriorated masonry $2,500 to $7,000
    Chimney removal above the roofline Unused chimney, roof replacement planned $1,000 to $3,500

    Masonry and liner work is best planned in summer or early fall. If roof work is also needed, coordinate both jobs so the flashing is done once; our ice dams guide explains why leaks around chimneys often get worse in late winter.

    How to hire a chimney sweep: checklist

    • Ask whether the technician is trained for your type of appliance, and whether the company belongs to the Association des professionnels du chauffage (APC), the Quebec association of heating professionals.
    • Confirm the company holds liability insurance, since the work is done on your roof.
    • For masonry, liner or structural repairs, check the contractor’s licence with the Régie du bâtiment du Québec.
    • Get a written price that states what is included: smoke pipe, inspection, report, travel.
    • Ask for photos of problem areas before agreeing to repairs, and request a separate quote for any work beyond the sweep.
    • Keep the receipt or report. Your insurer may ask for proof of maintenance after a claim.

    Comparing several offers is the simplest way to know whether a price is fair. On our chimney sweep, fireplace and stove quotes page you can describe your appliance and receive up to 4 free quotes from local companies serving Montreal, Laval, the South Shore, the North Shore and the West Island.

    Frequently Asked Questions

    How much does it cost to have a chimney swept in Quebec?

    In 2026, a routine sweep of one wood stove or fireplace flue generally costs between $150 and $350 before taxes. Visits that include a detailed inspection report or a camera scan usually run $250 to $500.

    Is chimney sweeping mandatory in Quebec?

    There is no single province-wide schedule imposed on every homeowner, but some municipal fire safety bylaws require chimneys to be kept clean, and fire services recommend at least one sweep a year for appliances in regular use. Your home insurance policy may also require proof of maintenance, so read its wording.

    What is the best time of year to sweep a chimney?

    The Government of Quebec recommends spring, when deposits are dry and there is time to make repairs before the heating season. Fall works too, but expect longer wait times in October and November.

    Can I sweep my own chimney?

    Some homeowners with a single-storey house, the right brushes and safe roof access clean their own flue. A professional visit remains the best way to spot cracks, liner damage or clearance problems that a brush will not reveal, and working on a roof in cold weather carries a real fall risk.

    How long does a chimney sweep take?

    A standard sweep of one flue usually takes 45 minutes to 1.5 hours. Glazed creosote, several appliances or repairs extend the visit.

    Get up to 4 free chimney sweep quotes

    Tell us about your stove, insert or fireplace and where you live, and we will connect you with up to 4 qualified local companies. It is free and there is no obligation. Get my free quotes

  • Quotes for Roof Repairs: How to Get, Read and Compare Them

    In short: a good quote for a roof repair names the exact problem, the exact fix, the materials, the area in square or linear feet, the price before taxes, the warranty and the roofer’s RBQ licence number. Get at least three written quotes built on the same scope of work, compare them line by line rather than by total, and be wary of any quote that is far below the others or asks for a large cash deposit.

    Asking for quotes for roof repairs sounds simple: call a few roofers, wait for the numbers, pick the lowest. In practice, most homeowners in Montreal and the rest of Quebec end up with three documents that do not describe the same job. One roofer quotes a few shingles, another quotes a full section with new underlayment, a third sends a single line that says “repair roof leak – $1,200”. Comparing them is like comparing three restaurant bills without the menu.

    This guide is the complete method for getting roof repair quotes you can actually trust and compare. It covers what to prepare before you call, what a complete quote must contain, how roofers build their prices, how to compare offers side by side, which warning signs should make you walk away, and what to check before you sign. It applies to sloped shingle roofs, metal roofs and flat roofs on duplexes, triplexes and commercial buildings.

    Why roof repair quotes vary so much

    It is common to receive roof repair quotes that differ by 50% or even 100% for what looks like the same job. That does not automatically mean someone is overcharging. Prices move with several factors that the homeowner rarely sees:

    • The diagnosis itself. A leak that shows up in your ceiling can start several feet away from the stain. One roofer may plan to replace a cracked vent boot; another may have found that the flashing along the chimney is the real culprit. Different diagnoses lead to different prices.
    • The scope. “Replace damaged shingles” can mean five shingles or a 10 by 10 foot section with new underlayment and ice and water shield. The second job costs several times more, and it may be the right one.
    • Access and safety. A steep roof on a three-storey building in the Plateau, a roof with no place to set a ladder, or a job that requires a lift or scaffolding costs more than a low bungalow roof in a suburb.
    • Minimum charges. Most companies have a minimum service charge that covers travel, setup and insurance. A five-minute fix still costs that minimum.
    • Warranty and overhead. A licensed, insured company that offers a written warranty on its work has costs that an uninsured individual does not, and its prices reflect that.

    For typical price ranges by type of repair, including inspections, shingle sections, vent boots, chimney flashing and flat roof patches, see our roof repair price list for Montreal homes. Keep it open while you read your quotes: it gives you a reference point for each line.

    Before you ask for quotes: prepare your roof file

    The more precise the information you give, the more precise and comparable the quotes you receive. Fifteen minutes of preparation saves days of back-and-forth.

    1. Document the problem

    • Take dated photos of every symptom: water stains on the ceiling, drips in the attic, missing or curled shingles visible from the ground, granules in the gutters, blistered membrane on a flat roof.
    • Note when the problem appears: only during heavy rain, during snowmelt, when wind blows from a certain direction, or all the time. Leaks that appear only during thaw often point to ice dams rather than a hole in the roof.
    • If you can safely access the attic, look for wet insulation, dark stains on the roof deck or daylight coming through.

    2. Gather the basic facts about your roof

    • Type of roof: asphalt shingles, metal, elastomeric membrane, TPO, EPDM, tar and gravel.
    • Approximate age of the roof covering and date of the last repair, if you know it.
    • Number of storeys and how the roof is accessed.
    • Any previous warranty documents from the roofer who installed it. Some repairs may still be covered.

    3. Decide what you are asking for

    Be clear in your request: do you want a repair of a specific problem, an inspection with a report and a recommendation, or a comparison between repairing and replacing? If your roof is near the end of its life, a repair quote alone may not answer your real question. Our guide on whether to repair or replace a flat roof helps you make that call, and the article on what a roof replacement estimate should include covers the other side of the decision.

    How many quotes should you get?

    For most roof repairs, three written quotes is the right number. One quote gives you no reference point. Two quotes that disagree leave you with no tie-breaker. Three quotes usually reveal a pattern: two prices in the same range and one outlier, or one diagnosis that differs from the others. Beyond four or five quotes, you mostly spend time without learning anything new. We explain this in more detail in how many roof repair estimates you should get.

    The exception is a true emergency. If water is coming into your home during a storm, the priority is a temporary protection such as a tarp or an emergency patch, from the first qualified roofer who can come. You can then take the time to collect proper quotes for the permanent repair. See our article on emergency roof repairs for what counts as an emergency and what it typically costs.

    To save time, you can request several quotes at once instead of calling roofers one by one. Our page on getting multiple roof repair quotes fast explains how, and Estimations Pro can put you in touch with up to four roofers in your area with a single free request.

    Get up to 4 free roof repair quotes

    Describe your roof problem once and receive quotes from roofing contractors in Montreal and surrounding areas. Free, no obligation.

    Request my quotes

    What a complete roof repair quote must include

    A serious roof repair quote is a written document, not a number sent by text message. Use this list as a checklist. If an item is missing, ask the roofer to add it before you compare.

    ItemWhat to look for
    Company identificationLegal business name, address, phone, NEQ and RBQ licence number
    DiagnosisWhat is wrong and where: “cracked rubber boot on plumbing vent, north slope”, “lifted flashing at chimney base”
    Detailed scope of workEach task listed: remove, replace, seal, install, clean up
    QuantitiesSquare feet of shingles or membrane, linear feet of flashing, number of vents or drains
    MaterialsBrand and product line, type of underlayment, type of sealant or membrane
    Hidden damage clausePrice per sheet of plywood or per square foot of deck if rot is found once the roof is opened
    PriceTotal before taxes, then GST and QST shown separately
    Payment termsDeposit amount, schedule, accepted payment methods
    ScheduleEstimated start date and duration, weather conditions
    WarrantyWorkmanship warranty in years, in writing, plus manufacturer warranty on materials
    Cleanup and disposalRemoval of debris, magnet sweep for nails, container if needed
    ValidityHow long the price is valid (often 15 to 30 days)

    On a flat roof, also look for details on the membrane system (elastomeric, TPO or EPDM), the treatment of drains and parapets, and how the new section will be joined to the existing membrane. Our comparison of elastomeric, TPO and EPDM membranes will help you understand what you are being offered.

    How roofers build the price of a repair

    Understanding the structure of a price helps you ask the right questions instead of simply asking for a discount. Most roof repair quotes combine five components:

    1. Minimum charge or mobilization. Travel, loading, ladders or lift, safety equipment and setup. Often between $150 and $400 for a simple call in Greater Montreal, sometimes credited against the repair.
    2. Labour. Usually the largest part. It depends on the time on the roof, the size of the crew and the difficulty of access. Steep or high roofs require more safety measures and slower work.
    3. Materials. Shingles, underlayment, ice and water shield, flashing, sealants, membrane, vents. On small repairs, materials are often a small share of the total.
    4. Disposal. Removal of old materials and, for larger repairs, a container rental.
    5. Overhead and margin. Insurance, licence, vehicles, administration, warranty reserve and profit. A legitimate company must cover these costs to stay in business and honour its warranty.

    This is why a very small repair can seem expensive: the fixed costs are spread over a short job. If you have several small problems, ask for them to be quoted together. Grouping work into one visit is one of the most effective ways to lower the cost per repair. For a deeper look at what drives roofing prices, read why roofers are so expensive.

    How to compare roof repair quotes line by line

    Once you have three written quotes, resist the urge to look at the totals first. Follow these steps instead.

    Step 1: Check that the diagnoses agree

    Put the three diagnoses side by side. If all three roofers identify the same cause, you can be fairly confident about the problem. If one of them sees something the others missed, call that roofer and ask them to explain, ideally with photos. Then ask the other two whether they checked that area. A good roofer will not be offended by the question.

    Step 2: Normalize the scope

    Make a simple table with one row per task and one column per roofer. Mark which tasks each quote includes. You will often find that the cheapest quote leaves out underlayment, flashing replacement, cleanup or the treatment of hidden damage. Ask the roofers whose quotes are incomplete to price the missing items, so that all three quotes cover the same work.

    Step 3: Compare quantities and unit prices

    If one quote says 80 square feet and another says 200 square feet for the same damaged area, one of them has measured differently or plans a larger repair. Ask why. Then compare unit prices, such as price per square foot of shingles or per linear foot of flashing, rather than totals alone.

    Step 4: Compare materials and warranty

    A quote that uses a basic three-tab shingle without new underlayment, with a one-year workmanship warranty, is not equivalent to one that uses architectural shingles, new ice and water shield and a five-year warranty. The second one may be worth the higher price. Put the warranty length and what it covers in your comparison table.

    Step 5: Look at the total cost, including risk

    Only now compare totals, taxes included. Add the possible cost of hidden damage using the unit price each roofer gave you. A quote that looks cheaper can become the most expensive one if its price for rotten decking is high and the roof is old.

    Example: three quotes for the same leak

    A homeowner in Rosemont has a leak near the chimney of a 20-year-old shingle roof. Quote A: $450, “reseal chimney with caulking”, 1-year warranty. Quote B: $950, “remove shingles around chimney, replace step and counter flashing, new ice and water shield, reinstall shingles”, 5-year warranty. Quote C: $2,400, “replace the entire slope”. Quote A treats the symptom and is likely to fail again within a season or two. Quote C may be justified if the slope is at the end of its life, which the homeowner should ask about. Quote B addresses the cause with a solid warranty and is, in most cases, the best value.

    We describe a general comparison method in our French guide on comparing contractor quotes in 7 steps, which also applies to roofing.

    Red flags in a roof repair quote

    Some warning signs should make you slow down or walk away entirely:

    • No RBQ licence number on the quote, or a number that does not match the company name.
    • A price far below the others without a clear explanation. It often means missing work, low-quality materials, no insurance or a plan to add extras once the job has started.
    • A large cash deposit requested before any material is delivered, or a request to pay everything upfront.
    • Pressure to sign immediately: “this price is only valid today”, “we have a crew in your area this afternoon”.
    • Unsolicited visits after a storm by someone who “noticed damage” on your roof from the street.
    • A vague one-line quote, such as “fix leak”, with no diagnosis, no quantities and no materials.
    • No written warranty, or a warranty that is only verbal.
    • No taxes on the quote, or an offer of a lower price “without invoice”.
    • A diagnosis you cannot verify: refusal to show photos of the damage or to let you see the problem.

    Our article on red flags when hiring a roofer lists 14 warning signs in detail, and roofer scams and how to protect yourself covers the most common schemes seen in Quebec.

    Check the roofer before you accept a quote

    The best quote is worthless if the company cannot or will not stand behind it. Before you sign, take a few minutes to verify:

    • The RBQ licence. In Quebec, a contractor who does roofing work for others must hold a licence from the Régie du bâtiment du Québec with the right subcategory. You can check the licence, its status and its subcategories in the Régie du bâtiment du Québec licence holder register.
    • Liability insurance. Ask for a certificate of insurance. Work at height carries real risks, and you do not want an accident on your property to become your problem.
    • References and recent work. Ask for two or three recent clients with similar repairs, ideally in your area, and look at reviews that describe the work in detail. Our guide on what to look for in roof repair reviews explains how to tell useful reviews from noise.
    • Consumer protection. If the contract is signed at your home after an unsolicited visit, special rules for itinerant merchants may apply, including a cancellation period. The Office de la protection du consommateur explains your rights.

    For a step-by-step method, read how to verify a roofer’s licence and references and what licence and insurance a roofer needs in Quebec.

    Questions to ask each roofer about the quote

    A short call after receiving each quote often clarifies more than another visit. Ask what exactly causes the problem and how it was confirmed, whether you can see photos of the damage, whether the repair will last or is a temporary fix, how much life the rest of the roof has, what happens if rotten decking is found, who will do the work, and what the written warranty covers. Our full list is in questions to ask before hiring a roofer.

    Paying for the repair

    For small repairs, payment is usually made in full when the work is done. For larger repairs, a reasonable deposit to cover materials is common, with the balance on completion and after your inspection of the work. Avoid paying in cash without a receipt, and keep all documents: the quote, the contract, the invoice, the warranty and before-and-after photos. To discuss price without cutting corners, group several small repairs into one visit and stay flexible on timing; our guide on how to negotiate roofing costs explains more.

    If the repair is large, compare payment options in our article on roof repair financing options in Quebec. Some roof-related work may also be linked to energy efficiency or other programs; our guide on the roof repair tax deduction in Quebec explains what really qualifies and what does not.

    Repair quote or replacement quote?

    Sometimes the most useful quote is the one that tells you not to repair. If your roof is near the end of its expected life, has several leaks, or shows widespread wear such as curled shingles, missing granules or a blistered membrane, a series of repairs can cost more over a few years than a replacement. Ask at least one roofer to give you both options: the price of the repair and an estimate for replacement, with their honest opinion on which makes more sense.

    For reference, see our guides on the average cost to replace a roof in Montreal, the cost of a new roof in Canada and roofing material costs compared. If you have a flat roof, how long a flat roof lasts will help you judge whether a repair is still worth it.

    Compare roof repair quotes the easy way

    One free request, up to four roofing contractors in your area. You choose, with no obligation.

    Get my free quotes

    Frequently asked questions

    Are roof repair quotes free?

    Most roofers in Quebec provide free quotes for standard repairs when they can see the problem from the ground, from a ladder or from photos. A detailed inspection with a written report, or a visit that requires special equipment, may be charged. Ask before the visit, and ask whether the fee is credited if you hire the company.

    Can a roofer give me a quote from photos only?

    Photos are useful for a first estimate, especially for simple items such as a missing shingle or a damaged vent. For leaks, a visit is usually needed, because the source of the water is often not where the stain appears. Treat a quote based only on photos as preliminary.

    What if the roofer finds more damage during the repair?

    This is common on older roofs. A good quote includes a unit price for additional work, such as replacing a sheet of plywood. If the quote does not, ask the roofer to stop, show you the damage and give you a written price before continuing.

    Is the lowest quote always a bad sign?

    No. Sometimes a roofer has lower costs, a crew nearby or a slow week. A low quote becomes a red flag when it is far below the others without a clear reason, when it leaves out tasks the others include, or when it comes with a short or verbal warranty.

    Prices in this guide are indicative ranges observed in Greater Montreal in 2026, before GST and QST. They are not official rates and do not replace a written quote based on an inspection of your roof. Licensing and consumer protection rules are summarized for general information; refer to the Régie du bâtiment du Québec and the Office de la protection du consommateur for the official rules.

  • Backwater Valve Cost in Montreal: 2026 Prices and Grants

    Backwater valve cost in Montreal in 2026 typically runs from about $400 to $1,500 installed when the drain pipe is exposed, and from $2,000 to $5,000 when a plumber has to cut through the basement slab to reach it. For most homes on the island, in Laval or on the South Shore, it is one of the cheapest ways to avoid a sewer backup that can ruin a finished basement after a summer downpour or a winter rain-on-snow event.

    In short: exposed pipe usually means under $1,000; under an existing slab, plan for $2,000 and up. Montreal’s bylaw 11-010 requires valves in new buildings and on the fixtures of buildings that have already had a backup. Quebec’s new Rénoclimat Adaptation stream pays up to $700 for an eligible valve, and the City’s RénoPlex program can help plex owners. All prices below are indicative 2026 ranges, before GST and QST, not official rates.

    Backwater valve cost in Montreal at a glance (2026)

    These ranges reflect typical residential jobs in Greater Montreal. Your real price depends on access, pipe size, the valve type your plumbing allows and how much floor has to be rebuilt afterwards.

    Job When it applies Indicative installed price (2026)
    Valve on an exposed fixture drain Unfinished basement, pipe visible $400 to $1,000
    Main valve on the building drain, accessible Protects the whole basement in one spot $700 to $1,500
    Valve under an existing concrete slab Floor drain or basement toilet below grade $2,000 to $5,000
    Camera inspection of the sewer lateral Older cast-iron or clay pipe, unknown slope $200 to $500
    Access box or cover in a finished floor Developed basement $150 to $600
    Retention pit with sump pump Fixtures below sewer level, combined systems $1,500 to $4,000
    Battery backup for an existing sump pump Power outages during storms $500 to $1,500
    Service call: cleaning, new gasket or flap Existing valve that sticks or leaks $150 to $400

    Add 14.975% for GST and QST: a $1,200 job becomes roughly $1,380 once taxes are included.

    What a backwater valve does (and what it is not)

    A backwater valve sits on the drain line that carries wastewater out of your basement. Water flows out to the municipal sewer normally, but a flap or gate closes when the sewer surcharges and tries to push water back toward the house. Without it, overloaded pipes can force sewage up through the floor drain, basement toilet, shower or laundry tub.

    Many older Montreal neighbourhoods are served by combined sewers, where storm runoff and household wastewater share the same pipe. During intense rain those pipes fill fast. Homes with basements below street level, driveways that slope toward the house or rain leaders connected to the sewer are the most exposed.

    Do not confuse it with a backflow preventer. That device protects the drinking water supply from contamination and falls under separate Régie du bâtiment du Québec rules; the RBQ page on backflow prevention devices notes that existing fully residential buildings with fewer than 9 units or fewer than 3 storeys are excluded from those obligations. A backwater valve is about sewage coming back in, not clean water going out.

    Normally open vs normally closed: which backwater valve does your home need?

    Montreal borough guides describe two families of valves, and the right choice is a plumbing decision, not a price decision:

    • Normally closed valve: the gate stays shut and opens only to let wastewater out. Municipal guides recommend this type on fixtures for buildings with a flat roof, which covers most duplexes, triplexes and plexes on the Plateau, in Rosemont, Villeray or Verdun, where interior rain leaders often tie into the drain.
    • Normally open valve: installed on the main building drain, it stays open so air and water circulate, and closes only during a backup. City guides present it mainly as an alternative for single-family homes with a sloped roof whose rainwater is not piped into the sewer.
    • Retention pit with pump: when fixtures sit below the level the sewer can surcharge to, a sealed pit and pump lift water above that level, with its own check valve.

    Some municipalities around Montreal forbid certain setups, such as a valve on the main collector or insert-type “squeeze” valves, so a local licensed plumber should confirm what your town accepts before quoting.

    What drives backwater valve installation cost

    • Concrete work. Saw-cutting, breaking and digging down to the pipe, then pouring a new patch, is the single biggest cost driver.
    • Finished floors. Removing and reinstalling ceramic, vinyl plank or carpet around the access point adds labour and materials.
    • Number of fixtures. A basement with a toilet, shower, laundry and floor drain may need several valves or one well-placed main valve, depending on venting.
    • Pipe condition. Cracked cast iron or clay found during the job can turn a valve install into a partial drain replacement. A camera inspection first avoids surprises.
    • Permits and certificate. Some boroughs and suburbs require a permit for slab openings or plumbing changes, and a certificate of conformity is often needed for grants.
    • Timing. Calls placed the morning after a storm cost more and wait longer than work booked in the fall or early spring.

    If water also seeps along the walls or the edge of the slab, the issue may be your foundation drainage rather than the sewer; compare French drain replacement quotes before spending on the wrong fix.

    Is a backwater valve mandatory in Montreal?

    Yes, in several situations. According to the City of Montreal’s guidance on montreal.ca, its bylaw on protecting buildings against sewer backups (11-010) has required backwater valves in all new buildings since 2011, and installing a valve on each plumbing fixture is mandatory for a building that has already been flooded or had a sewer backup. The valves must stay accessible, so a new floor cannot simply cover them.

    Laval, Longueuil and many South Shore and North Shore towns have similar bylaws. A common clause states that the municipality is not liable for backup damage when a building is not protected as required. Your insurer may also ask whether valves are present before offering or renewing sewer-backup coverage, so check your municipality’s bylaw and your policy wording.

    Grants that reduce backwater valve cost in 2026

    Program Who it targets Support related to a backwater valve
    Rénoclimat Adaptation, simplified path (Government of Quebec) Principal residences and multi-unit residential buildings Up to $700 for a backwater valve; sump pump with battery up to $1,000; removable flood barrier up to $800
    RénoPlex (City of Montreal) Houses and buildings with 5 dwellings or fewer in Montreal Flood-protection work over $500; the City lists amounts such as $560 per normally closed valve under an existing slab and $1,500 for a retention pit with pump

    Rénoclimat details are on the Government of Quebec’s Rénoclimat Adaptation page; work must be done after October 1, 2026 by a properly licensed contractor. RénoPlex conditions are published by the City of Montreal on montreal.ca. Our explainers on the Rénoclimat flood grant and the RénoPlex program cover eligibility, and the full list is in our Quebec renovation grants guide. Confirm current criteria before you sign a contract, since amounts and filing rules can change.

    How a backwater valve is installed: 7 steps

    1. Assessment: the plumber maps basement fixtures, the building drain and venting, and scopes the sewer lateral by camera if needed.
    2. Valve choice: one main valve or one per fixture, normally open or normally closed, plus the access location.
    3. Written quote: model, number of valves, concrete and flooring repair included or not, warranty and timeline.
    4. Permit: filed with the borough or town when required.
    5. Installation: slab opened if necessary, valve set level and in the correct flow direction, with a clean-out or access riser.
    6. Testing and closing: the flap is tested, the trench backfilled, and concrete and flooring restored.
    7. Paperwork: invoice, valve model, photos and a signed certificate of conformity, which you will need for grants and insurance.

    Hire a plumbing contractor holding the right Régie du bâtiment du Québec licence; Montreal recommends a member of the Corporation des maîtres mécaniciens en tuyauterie du Québec (CMMTQ). Comparing several detailed bids is the best way to spot a missing line item, which is why our plumber quotes page lets you request up to four.

    Backwater valve maintenance checklist

    • Open the access cover and remove debris, grease and hair from the flap and seat.
    • Check the gasket for cracks and the flap for free movement.
    • Make sure nothing (boxes, furniture, new flooring) blocks the access.
    • Test before the spring thaw and again before summer storm season; the City suggests checking about twice a year.
    • Keep roof drains and downspouts discharging away from the foundation where your bylaw allows it.

    Protect your basement before the next storm

    Describe your basement once and receive up to 4 free quotes from licensed plumbers in Montreal, Laval, Longueuil and the West Island.

    Get up to 4 free quotes

    Frequently Asked Questions

    How much does it cost to install a backwater valve in Montreal?

    Expect roughly $400 to $1,500 before tax when the pipe is accessible, and $2,000 to $5,000 when the slab must be opened and rebuilt. Grants can cover part of eligible work.

    Is a backwater valve worth it?

    For a finished basement on a combined sewer, usually yes: one backup can cost far more in cleanup, drywall and flooring than the valve itself. If you have already had water in the basement, see our basement water damage cleanup quotes page.

    Does home insurance require a backwater valve?

    Policies differ. Many insurers ask about valves before offering sewer-backup coverage, and some municipalities refuse liability if a required valve is missing. Read your policy and ask your broker.

    How often should a backwater valve be cleaned?

    At least once a year, ideally checked twice: before the spring melt and before summer storms. Valves serving a laundry or kitchen fixture may need more frequent cleaning.

    Can I install a backwater valve myself?

    Plumbing work in Quebec must meet the Construction Code, and grants such as Rénoclimat require a licensed contractor and a certificate of conformity. A DIY install also risks choosing the wrong valve type for your venting.

    Lire en français : clapet antiretour, prix et installation.

  • Heat Pump Installation Cost in Quebec: 2026 Price Guide

    Heat pump installation cost in Quebec in 2026 usually ranges from about $3,500 for a single wall-mounted mini-split to $12,000–$20,000 for a ducted central system, before tax and before grants. Geothermal systems sit in a different league, often $30,000 or more because of drilling. Where your project lands depends on the type of system, the heating capacity you need for a Quebec winter, the electrical work and how easy the installation is.

    In short: for most Montreal-area homes heated with electric baseboards, a cold-climate mini-split (or two) is the most affordable way to cut heating bills and add air conditioning. Homes that already have ducts get the most out of a central heat pump. Hydro-Québec’s LogisVert program is now the main Quebec subsidy for heat pumps, and a new federal rebate has been announced. All prices in this guide are indicative 2026 ranges, not official rates.

    Heat pump installation cost in Quebec at a glance (2026)

    The table below shows typical installed prices for an average home in the Greater Montreal area (Montreal, Laval, Longueuil, the South Shore and North Shore). They include the equipment, line set, mounting, a dedicated circuit in a panel with room to spare, commissioning and disposal of packaging, but not sales tax.

    System type Typical capacity Indicative installed price (2026) Best for
    Wall mini-split, single zone (standard) 9,000 to 12,000 BTU/h $3,500 to $5,500 One open area, condo, bedroom addition
    Wall mini-split, single zone (cold climate) 12,000 to 24,000 BTU/h $4,500 to $8,000 Main floor of a bungalow or plex unit
    Multi-zone mini-split (2 to 4 indoor heads) 18,000 to 36,000 BTU/h $8,000 to $16,000 Whole home on baseboards, several closed rooms
    Central ducted heat pump (existing ducts) 24,000 to 48,000 BTU/h $9,000 to $16,000 Homes with a forced-air furnace
    Central heat pump + new air handler or electric furnace 24,000 to 48,000 BTU/h $12,000 to $20,000 Replacing an old furnace and central air together
    Geothermal (ground-source) system 3 to 5 tons $30,000 to $50,000+ Large lots, long-term owners, rural homes

    Adding ductwork to a home that has none is a separate project and can add several thousand dollars on top of a central system, which is why most baseboard-heated homes in Quebec choose ductless units instead.

    Mini-split, central or geothermal: which fits your home?

    Ductless mini-split

    A wall unit inside is connected to an outdoor compressor by refrigerant lines through a small hole in the wall. It is the go-to option for duplexes, triplexes and bungalows heated with baseboards. One head heats an open space well, but closed bedrooms stay cooler, so baseboards remain as backup. Our page on ductless mini-split heat pump quotes explains what installers need to see before pricing.

    Central (ducted) heat pump

    The outdoor unit replaces or complements a central air conditioner and pushes heat through the existing ducts. It distributes heat evenly to every room and works with an electric furnace or a dual-energy setup for the coldest nights. Duct condition, return air and the age of the furnace drive the price.

    Geothermal heat pump

    A ground loop drilled or trenched on your lot gives the most stable performance in deep cold, but the up-front cost and the need for space and access limit it mostly to detached homes outside dense neighbourhoods.

    What drives the cost of a heat pump installation

    • Heating capacity at low temperature. In Quebec, what matters is how much heat the unit still delivers at −15 °C to −25 °C, not its nominal rating. Cold-climate models cost more but keep baseboards off longer.
    • Number of zones. Each extra indoor head adds equipment, line set, condensate drain and labour.
    • Line set length and routing. Long runs, finished walls, brick facades or a third-floor unit in a Plateau triplex mean more time and materials.
    • Outdoor unit support. A ground stand above the snow line, a wall bracket or a roof curb on a flat roof each has its own price, plus a snow cover or deflector in many cases.
    • Electrical capacity. A heat pump needs a dedicated circuit. If the panel is full or only 100 A, an upgrade may be needed; see our page on electrical panel upgrade quotes.
    • Removal of old equipment. Taking out an oil furnace and tank, or an old central air unit, adds disposal and sometimes decontamination costs.
    • Brand, warranty and season. Fall is peak demand for heating installs; booking in late summer or early spring often makes scheduling easier.

    Sizing a heat pump for a Quebec winter

    Undersizing is the most common complaint after an installation: the unit runs non-stop and baseboards still carry the load in January. Oversizing is not better, because a unit that is too big cycles on and off, controls humidity poorly in summer and costs more. A serious contractor bases the size on a heat-loss calculation that considers insulation, windows, air leakage and the layout of the rooms, not just square footage. If your attic or basement is poorly insulated, fixing that first can let you buy a smaller, cheaper system.

    As a rough reference only, an open main floor of 800 to 1,000 sq ft in a reasonably insulated Montreal home often calls for a cold-climate unit in the 12,000 to 18,000 BTU/h range, while a full two-storey house usually needs a central or multi-zone system. Ask each installer to state the heating capacity at −15 °C and the lowest operating temperature in writing.

    Grants and rebates that lower heat pump installation cost in 2026

    The subsidy landscape changed a lot in 2026, so check each program’s status before you sign:

    Program Status (November 2026) What it means for you
    LogisVert (Hydro-Québec) Open Main Quebec subsidy for heat pumps; amount based on heating capacity at −8 °C, higher for cold-climate models, up to about $6,700 for an air-to-air system. The model must be on the eligible list.
    Rénoclimat (Government of Quebec) Open, but no longer funds heating systems Still useful for insulation, air sealing, windows and ventilation done alongside the heat pump.
    National Heat Pump Rebate (federal) Announced October 2026, applications not open yet Up to $10,000 for eligible below-median-income households and $2,000 for other eligible households, according to the federal announcement.
    Chauffez vert Ended No longer accepting applications.
    Oil to Heat Pump Affordability (federal) Closed to new applications since July 31, 2026 Only files already approved can still be completed.

    Sources to confirm: the Government of Quebec page on Rénoclimat and mechanical systems, the Prime Minister’s announcement of the National Heat Pump Rebate and Natural Resources Canada’s Oil to Heat Pump Affordability page. For LogisVert amounts and the list of eligible models, consult the participant guide on the Hydro-Québec website. Our detailed guides cover the LogisVert heat pump rebate and how to combine LogisVert and Rénoclimat.

    Do not forget sales tax: in Quebec, GST (5%) and QST (9.975%) add roughly $1,500 to a $10,000 installation.

    How to get an accurate heat pump quote: 7 steps

    1. Gather your numbers: recent Hydro-Québec bills, square footage, number of floors and current heating type.
    2. Decide your goal: heating a main floor, the whole house, or replacing an end-of-life furnace or air conditioner.
    3. Check the contractor’s licence: make sure the company holds a valid licence on the Régie du bâtiment du Québec website, and that the technicians who handle refrigerant are qualified to do so.
    4. Ask for an on-site visit rather than a phone price, so the installer can see the panel, wall construction and outdoor location.
    5. Request the heat-loss basis for the size proposed and the capacity at low temperature.
    6. Compare at least three written quotes with the same scope, using the checklist below.
    7. Confirm grant eligibility before signing: exact model number, installation requirements and who files the application.

    Quote checklist

    • Brand, model numbers of indoor and outdoor units, and heating capacity at −15 °C
    • Line set length included and the price per extra foot
    • Outdoor support (stand, bracket or roof curb) and snow protection
    • Electrical work, breaker and disconnect, and whether a permit or declaration is included
    • Condensate drain routing and any wall patching or painting
    • Manufacturer warranty, labour warranty and registration
    • Thermostat or controls setup with your baseboards or furnace
    • Removal of old equipment and clean-up

    In Montreal, some boroughs regulate where an outdoor unit can be placed and how much noise it can make near a property line, so ask your installer to confirm the rules with your borough before the work starts.

    Operating and maintenance costs after installation

    A heat pump does not eliminate heating costs; it reduces how often your baseboards or furnace run. Savings depend on the size of the home, insulation and how cold the winter gets. Budget for yearly maintenance: cleaning filters every month or two during heavy use, and a professional check-up every one to two years, often in the $150 to $300 range. Keep the outdoor unit clear of snow and ice, and never let a roof drip line fall directly on it.

    Frequently Asked Questions

    How much does it cost to install a heat pump in Quebec?

    Most homeowners pay $3,500 to $8,000 for a single mini-split, $8,000 to $16,000 for a multi-zone system and $9,000 to $20,000 for a central ducted system in 2026, before tax and grants.

    Is a heat pump worth it in Quebec’s cold climate?

    For most homes, yes, as long as you choose a cold-climate model sized for your home. Electric baseboards or a furnace still handle the coldest days, but the heat pump covers most of the season and adds air conditioning in summer.

    Can I get a grant for a heat pump in Quebec in 2026?

    Yes. LogisVert from Hydro-Québec is the main program for heat pumps. Rénoclimat no longer funds heating systems, and the new federal National Heat Pump Rebate had been announced but was not yet accepting applications in November 2026.

    How long does a heat pump installation take?

    A single mini-split is usually installed in one day. Multi-zone and central systems often take one to three days, plus any electrical upgrade or duct modifications.

    How long does a heat pump last?

    With regular maintenance, many heat pumps last roughly 15 years, sometimes more. Coastal salt, poor drainage around the outdoor unit and lack of filter cleaning shorten that lifespan.

    Ready to compare prices? Describe your home once and get up to 4 free heat pump quotes from licensed contractors in Montreal, Laval, Longueuil, the North Shore, the South Shore and the West Island. You can also browse our heat pump and heating quotes page.