Obtenir 4 soumissions gratuites →Get 4 free quotes →Estimations.pro
Accueil / Soumissions

Baseboard Heater Size Calculator: Watts per Room (2026)

In short: a baseboard heater size calculator tells you how many watts a room needs. The common Canadian rule of thumb is about 10 watts per square foot for a room with 8 ft ceilings and average insulation, adjusted up for high ceilings, several exterior walls or big windows, and down for a recent, well-insulated house. Use the tool below for an indicative estimate, then have a licensed electrician confirm the circuit and compare up to 4 free quotes.

Get up to 4 free electrician quotes

Describe your heating project in 2 minutes, no obligation.

Get my quotes →

Baseboard heater size calculator

Enter the room size, then press Calculate.

How many watts per square foot for a baseboard heater?

Electric baseboard heaters turn almost all the electricity they draw into heat, so sizing them is simple arithmetic: you match the wattage to the heat the room loses on a cold day. Across Canada, electricians and manufacturers use a starting point of about 10 watts per square foot for a room with an 8 ft ceiling, standard windows and average insulation. A 12 x 11 ft bedroom (132 sq ft) therefore needs roughly 1,300 W, which in practice means a 1,500 W heater or two smaller units.

That figure moves with the house. A recent home built to modern energy codes, or an older one with new windows and a well-insulated attic, can be comfortable at 7 to 8 W per square foot. A pre-1970 plex with original walls, a three-season room or an uninsulated addition may need 12 to 15 W per square foot. Ceiling height matters too: a 10 ft ceiling adds about a quarter more air to heat, which is why the calculator raises the result for taller rooms.

Baseboard heater size chart by room

The table below applies the 10 W per square foot rule to common room sizes with 8 ft ceilings. Heaters are sold in standard steps, so the result is rounded up to the next available size or split between two units.

Room (example)AreaWatts needed (approx.)Typical setup
Small bathroom or office50 – 70 sq ft500 – 700 WOne 500 W or 750 W heater
Child’s bedroom90 – 110 sq ft900 – 1,100 WOne 1,000 W or 1,250 W heater
Master bedroom140 – 180 sq ft1,400 – 1,800 WOne 1,500 W or 2,000 W heater
Living room200 – 250 sq ft2,000 – 2,500 WTwo 1,250 W heaters
Open kitchen and dining area300 – 350 sq ft3,000 – 3,500 WTwo 1,500 W or 2,000 W heaters
Finished basement family room350 – 450 sq ft3,200 – 4,000 WTwo or three heaters on separate thermostats

Splitting a large room between two heaters, usually one under each window, gives more even comfort than one long unit at one end. In a basement, the walls below grade lose heat more slowly than above-grade walls, but a poorly insulated rim joist can cancel that advantage.

Circuits, amps and breakers: what your electrician checks

In Canadian homes, baseboard heaters normally run on 240 V. To find the current, divide the watts by 240: a 2,000 W heater draws about 8.3 A. Because heating is a continuous load, electricians keep a circuit to about 80% of its breaker rating. In practice, a 15 A, 240 V circuit carries up to about 2,880 W of heaters and a 20 A circuit about 3,840 W.

Adding heat to a room is therefore not only a question of the heater itself. Your electrician will check whether the existing circuit has room left, whether the panel has free spaces and whether the total load of the house still fits the service. Homes with an older 100 A panel sometimes reach their limit when heaters, a heat pump or an EV charger are added; our electrical panel upgrade quotes page explains that step.

In Quebec, electrical work must be done by a contractor holding the proper licence, generally issued through the Corporation des maîtres électriciens du Québec. You can confirm that a business holds a valid licence on the Régie du bâtiment du Québec website before you sign.

How much does it cost to run a baseboard heater in Quebec?

The running cost is the energy used multiplied by your electricity price. A 1,500 W heater running at full power for one hour uses 1.5 kWh. Thermostats cycle the heat, though, so a heater rarely runs all day: in a typical winter month it may be on about a third of the time, closer to half during a January cold snap.

Hydro-Québec’s residential Rate D has two tiers: a lower price for the first 40 kWh per day and a higher price for the rest. After the April 1, 2026 adjustment, the first tier is roughly 7 cents per kWh and the second roughly 11 cents; check the exact figures on your bill or on Hydro-Québec’s rate page. In winter, most electrically heated homes use well over 40 kWh per day, so the extra kilowatt-hours used for heating are mostly billed at the second tier. That is why the calculator starts at 11 cents. Outside Quebec, enter the price shown on your own utility bill.

HeaterMild month (20% run time)Typical winter month (35%)Cold month (45%)
1,000 W144 kWh – about $16252 kWh – about $28324 kWh – about $36
1,500 W216 kWh – about $24378 kWh – about $42486 kWh – about $53
2,000 W288 kWh – about $32504 kWh – about $55648 kWh – about $71

Estimates at 11 cents per kWh over 30 days, before taxes. Lowering the setpoint by a few degrees at night and in empty rooms, sealing drafts and adding attic insulation all cut these numbers. If your heating bills are high every winter, a heat pump may be worth pricing; our heat pump installation cost guide for Quebec compares the budgets.

Baseboard heater installation cost in 2026

Prices below are indicative ranges for the Montreal area in 2026, including the heater and labour by a licensed electrician, before taxes. Final quotes depend on access, wall type and the state of the electrical panel.

JobIndicative price (2026)
Replace an existing baseboard heater, same wattage$200 – $450 per heater
Add a heater on an existing circuit with spare capacity$250 – $600 per heater
New 240 V circuit with heater and thermostat$600 – $1,200
Electronic thermostat, supplied and installed$90 – $200 each
Smart Wi-Fi thermostat, supplied and installed$180 – $350 each

Replacing old mechanical thermostats with electronic models is one of the cheapest comfort upgrades in an electrically heated home: they hold the temperature within a narrow range instead of letting the room swing by several degrees.

Step by step: sizing and placing baseboard heaters

  1. Measure the room’s length and width and multiply them to get the area in square feet.
  2. Multiply by 10 W, then adjust for ceiling height, insulation, number of exterior walls and window area.
  3. Round up to a standard heater size, or split the total between two heaters if it exceeds about 2,000 W.
  4. Plan the location: under windows or along exterior walls, with furniture and curtains kept clear of the heater.
  5. Have an electrician confirm circuit capacity, breaker size and available panel spaces.
  6. Choose an electronic or smart thermostat for each room or zone.
  7. Compare at least three written quotes covering the same heaters, thermostats and wiring work.

Before buying more wattage for a cold room, look for the cause. Drafty windows and a thin attic layer are frequent culprits; signs such as heavy frost on the glass are covered in our article on window condensation in winter, and topping up the attic is often cheaper than adding heaters (see our attic insulation quotes).

Compare up to 4 licensed electricians

One short form, free quotes for heaters, thermostats and new circuits.

Get electrician quotes →

Frequently Asked Questions

What size baseboard heater do I need for a 12×12 room?

A 12 x 12 ft room is 144 sq ft. At 10 W per square foot with an 8 ft ceiling, it needs about 1,450 W, so a 1,500 W heater is the usual choice. A well-insulated recent home may get by with 1,250 W, while a corner room in an older house may need 1,750 to 2,000 W.

How many square feet will a 1,500 watt baseboard heater heat?

Using the 10 W per square foot rule, a 1,500 W heater covers roughly 150 sq ft with 8 ft ceilings and average insulation. In a well-insulated room that can stretch to about 190 sq ft; in a drafty room it may only cover 100 to 120 sq ft.

Is it better to have one large baseboard heater or two smaller ones?

For rooms over about 200 sq ft, or rooms with two windows, two smaller heaters usually give more even comfort, since each one counters the cold coming from its own wall. One larger heater is simpler and cheaper to install in a small room.

Can I install a baseboard heater myself in Quebec?

Baseboard heaters are wired on 240 V circuits, and in Quebec electrical installation work is reserved for licensed electrical contractors. Hiring one also protects your home insurance and ensures the circuit and breaker are sized correctly.

Do baseboard heaters use a lot of electricity?

Baseboard heaters convert nearly all their electricity into heat, but resistance heating is still more expensive to run than a heat pump, which moves heat instead of producing it. A 1,500 W heater running a third of the time uses about 380 kWh per month, which is why good thermostats and insulation matter.

Jusqu’à 4 soumissions gratuites

Une seule demande, des entrepreneurs de Montréal et des environs. Sans engagement.

Demander mes soumissions