In short: rough-in plumbing cost in Canada usually runs from about $450 to $1,200 per fixture in new construction in 2026, and 30% to 70% more in a renovation or a basement where the concrete slab has to be cut. A typical full bathroom (toilet, sink, shower) costs roughly $1,350 to $2,850 to rough in on open framing, and $4,000 to $9,000 or more under a basement slab. Use the calculator below for an indicative estimate, then compare up to 4 free quotes from licensed plumbers.
Rough-in plumbing cost calculator (Canada)
Enter your fixtures and press Calculate.
What is rough-in plumbing?
The rough-in is the plumbing that goes inside the walls, floors and ceilings before drywall, tile or concrete close everything up. It includes the drain, waste and vent (DWV) piping, the hot and cold water supply lines, the stubs where each fixture will later connect, and the venting that lets drains flow without siphoning traps. The finish stage, done later, is when the plumber sets the toilet, mounts the faucets and connects the appliances.
That is why plumbers often price the rough-in per fixture: each toilet, sink, shower or laundry hookup needs its own drain, vent connection and water lines. The fixture count is the quickest way to size the job, but the layout matters just as much as the number.
Rough-in plumbing cost per fixture in 2026
The ranges below are indicative prices for labour and rough-in materials (PVC or ABS drains, PEX or copper supply lines, fittings, vents) in 2026. They do not include the fixtures themselves, finishing work or taxes. They are based on market rates observed in Canadian cities and are not official prices.
| Fixture | New construction | Renovation (existing walls) |
|---|---|---|
| Toilet | $450 – $900 | $600 – $1,450 |
| Bathroom sink (lavatory) | $350 – $750 | $450 – $1,200 |
| Shower or bathtub | $550 – $1,200 | $700 – $1,900 |
| Kitchen or bar sink | $400 – $850 | $500 – $1,350 |
| Dishwasher or fridge water line | $175 – $400 | $225 – $650 |
| Laundry hookup (washer box and drain) | $350 – $750 | $450 – $1,200 |
| Floor drain | $300 – $650 | $400 – $1,050 |
| Water heater connection | $300 – $650 | $400 – $1,050 |
Prices in Toronto and Vancouver tend to sit 10% to 20% above Montreal, while smaller Quebec cities are often a little lower. Many plumbers also charge a minimum per visit, so a single-fixture rough-in rarely costs less than a few hundred dollars.
Rough-in plumbing cost for common projects
Most homeowners are not pricing one fixture but a whole room. Here is what typical projects look like in 2026, rough-in only:
| Project | Typical fixtures | Indicative rough-in cost |
|---|---|---|
| Powder room on open framing | Toilet, sink | $800 – $1,650 |
| Full bathroom, new construction | Toilet, sink, shower | $1,350 – $2,850 |
| Bathroom relocated in a renovation | Toilet, sink, tub | $2,300 – $5,500 |
| Basement bathroom under the slab | Toilet, sink, shower | $4,000 – $9,000+ |
| Kitchen with dishwasher | Sink, dishwasher | $600 – $1,800 |
| New single-family house | 8 to 15 fixtures | $7,000 – $20,000+ |
The basement figure jumps because the plumber has to saw and break the concrete, dig trenches to reach the main drain at the right slope, then patch the slab. If the new fixtures sit below the sewer line, a sewage ejector pump adds roughly $1,800 to $4,000.
What drives the cost of a plumbing rough-in?
- Distance to the main stack: fixtures grouped near the existing drain cost far less than a bathroom on the opposite side of the house.
- Access: open studs in new construction are fast; opening finished walls, ceilings or a concrete floor adds labour and repair work.
- Venting: every trap needs a vent. If a new vent has to go up through the roof, the price rises; an air admittance valve is only allowed where the code permits it.
- Pipe material: PEX is quicker to run than copper; ABS and PVC drains are standard, cast iron is mostly found in older Montreal plexes and complicates connections.
- Elevation: fixtures below the sewer line require an ejector pump, and Montreal requires backwater valves on fixtures located below ground level.
- Labour rates and permits: local hourly rates, travel and the municipal permit fee all show up on the quote.
Rough-in plumbing rules in Quebec and the rest of Canada
Plumbing is regulated provincially. In Quebec, plumbing work must meet Chapter III (Plumbing) of the Quebec Construction Code, and a contractor doing plumbing for you must hold a licence from the Régie du bâtiment du Québec (RBQ) with the appropriate plumbing subclass. You can check a contractor's licence number in the RBQ public register before signing anything. The applicable regulations are listed on the RBQ plumbing laws and codes page.
In the other provinces, the rules are based on the National Plumbing Code of Canada, adopted with provincial changes (for example the Ontario Building Code in Ontario). Across the country, adding or moving fixtures usually requires a municipal permit, and many cities inspect the rough-in before walls are closed. In Montreal, permits are issued by your borough, so requirements can vary between, say, Rosemont, Verdun and Saint-Laurent. Ask your plumber who files the permit and whether the price includes the inspection.
How to get an accurate rough-in plumbing quote
- Draw a simple plan showing where each fixture goes and where the existing stack and main drain are.
- List every fixture, including appliances people forget: fridge water line, laundry, floor drain, utility sink.
- Note the access: open framing, finished walls, concrete slab, crawl space.
- Ask for an itemized quote that separates rough-in, finish, materials, concrete work and permit fees.
- Verify the licence (RBQ number in Quebec) and the contractor's liability insurance.
- Compare at least three written quotes for the same scope, so you compare like with like.
Rough-in checklist before the walls are closed
- Drain slope checked and pipes properly supported
- Every trap vented according to code
- Pressure test or water test done on the new lines
- Stub-out heights and spacing match the fixtures you bought (toilet rough-in is usually 12 inches from the finished wall)
- Shut-off valves planned for each fixture
- Municipal inspection passed, if your city requires it
- Photos of the open walls kept for future repairs
Compare up to 4 free plumbing quotes
Licensed plumbers in Montreal, Laval, Longueuil and across Quebec. Free, no obligation.
Get my quotes →Frequently Asked Questions
How much does rough-in plumbing cost per fixture?
In 2026, expect roughly $450 to $1,200 per fixture in new construction in most Canadian cities, and up to about $1,900 per fixture when walls or floors must be opened. Small appliance lines like a dishwasher cost less; showers and tubs cost more.
How much does it cost to rough in a basement bathroom?
Because the concrete slab has to be cut and patched, a basement bathroom rough-in usually runs from about $4,000 to $9,000, and more if a sewage ejector pump or a backwater valve is required. Homes built with a capped basement rough-in already in place cost much less to finish.
Does rough-in plumbing need a permit?
In most municipalities, yes, when you add or move fixtures. Some cities also require an inspection before the walls are closed. Check with your city or borough, and confirm who applies for the permit before work starts.
How long does a plumbing rough-in take?
A bathroom on open framing often takes one to two days. A basement bathroom with concrete work can take three to five days, plus curing time for the patched slab. A whole house is usually spread over a week or more.
Can I do my own rough-in plumbing in Quebec?
Rules on homeowners doing their own work vary, and all work must still meet the Quebec Construction Code and pass any municipal inspection. Any contractor you hire must hold the proper RBQ licence. Mistakes in venting or slope are costly to fix once walls are closed, so most homeowners hire a licensed plumber for the rough-in.